The Acoustic Guitar Forum

Go Back   The Acoustic Guitar Forum > General Acoustic Guitar and Amplification Discussion > Build and Repair

Reply
 
Thread Tools
  #1  
Old 12-17-2011, 08:31 AM
Kitchen Guitars's Avatar
Kitchen Guitars Kitchen Guitars is offline
Formerly Yamaha Junkie
 
Join Date: Jun 2007
Location: South West Pennsylvania
Posts: 7,930
Default A tale of two Tenors - 2 Tenor Guitar Builds

I am wrapping up the "Peach" after a year of fiddling with her. So many new things. Cutaway, sound system, gloss finish...... Right now she is in the apply finish, wait 2 days.... mode so perfect opportunity to start up some new projects.
I have been wanting to build a Tenor Guitar for a few years now. I bought a few sets of plans from Elderlys.

Tenor 1 will be smaller than Tenor 2. I have decided to forgo the Ladder Bracing on 1 and do a X bracing instead
Tenor one is;
B/S - Leopardwood (Panopsis rebellens)
Top- Crazy Bear Claw Sitka
Tenor 2
B/S - Dead straight Dark Chocolate Indian Rosewood
Top - also Crazy Bear Claw Sitka

Both will likely have Walnut necks. I have a crapload of Walnut!
I promise lots of pictures!
I will be working off a Blue prints by Scott Antes.
I was going to start with The Tenor. Identical in size to my Regal (Fender era) Baritone Ukulele. However the top I joined and the 5 peice Lace back were both shy the needs. So.. The Regal Tenor is a bit smaller than the Tenor Tenor plan.
Total Body "15.56", Lower 10.5, Upper 7.5, Fret board length 14.13
I am going to start with the top at .10, 5 Piece back at 9.25, sides 8ish. I have read lacewood can be a tough bend. Thinned down it taps like Mahogany, to my ears.



I got this great Sitka from an A.S.I.A buddy.
I use some Sumistifikated methods!

This is the contrast bumped up a bit but NO finish. Still at 120

Today I will put in 5 skunk stripes and make my forms. BTW As I do this project I am also restoring a B A S K E T CA S E Oak Parlor I get a bit fidgety when my Christmas Photography Biz goes from 200 MPH to 10!
Reply With Quote
  #2  
Old 12-17-2011, 08:14 PM
Kitchen Guitars's Avatar
Kitchen Guitars Kitchen Guitars is offline
Formerly Yamaha Junkie
 
Join Date: Jun 2007
Location: South West Pennsylvania
Posts: 7,930
Default

Welp, killed the first back!
Reply With Quote
  #3  
Old 12-18-2011, 07:24 PM
Kitchen Guitars's Avatar
Kitchen Guitars Kitchen Guitars is offline
Formerly Yamaha Junkie
 
Join Date: Jun 2007
Location: South West Pennsylvania
Posts: 7,930
Default

Amazing what you can fix when you don't want to redo! Back on track. Will post more pictures when I know anyone gives a crap.
Reply With Quote
  #4  
Old 12-18-2011, 07:53 PM
thebolo thebolo is offline
Registered User
 
Join Date: Jan 2011
Location: Nebraska
Posts: 283
Default

I give a crap. Just sayin'
Reply With Quote
  #5  
Old 12-18-2011, 09:43 PM
kscobie8's Avatar
kscobie8 kscobie8 is offline
Whippersnapper
 
Join Date: Apr 2009
Location: Raleigh, NC
Posts: 6,656
Default

I know nothing about tenor guitars, but I do enjoy these build threads. Looking forward to this one. Bring it!


Bel isi,
-kyle
__________________
My neglected music blog:
www.kylescobie.com
Be sure to check out my brother's music:
www.kurtscobie.com
Reply With Quote
  #6  
Old 12-18-2011, 10:54 PM
gitnoob gitnoob is offline
Registered User
 
Join Date: Jun 2009
Location: Emerald City
Posts: 4,327
Default

Quote:
Originally Posted by Kitchen Guitars View Post
Amazing what you can fix when you don't want to redo! Back on track. Will post more pictures when I know anyone gives a crap.
Good luck. In my noob building class, a couple of noob-builders chose lacewood. I heard lots of cracking and swearing.

One guy had trouble with finish prep -- the back/sides ended up very textured even after sanding. Due to the varying density of the wood, I imagine.
__________________

gits: good and plenty
chops: snickers
Reply With Quote
  #7  
Old 12-19-2011, 07:53 AM
redcloud redcloud is offline
Registered User
 
Join Date: Mar 2010
Posts: 1,116
Default

John,

This should be fun to watch and for you to do. I have 2 Tenors: a Martin 0-18 Nick Reynolds Signature and A luthier-built 00 in Koa/Cedar.

Are you planning to tune yours C,G,D,A?
Reply With Quote
  #8  
Old 12-19-2011, 10:33 AM
Kitchen Guitars's Avatar
Kitchen Guitars Kitchen Guitars is offline
Formerly Yamaha Junkie
 
Join Date: Jun 2007
Location: South West Pennsylvania
Posts: 7,930
Default

Quote:
Originally Posted by redcloud View Post
John,

This should be fun to watch and for you to do. I have 2 Tenors: a Martin 0-18 Nick Reynolds Signature and A luthier-built 00 in Koa/Cedar.




Are you planning to tune yours C,G,D,A?
Lol I haven't gotten that far yet!

I was smitten with a OLD Martin Tenor Charley Rappaport (Conductor of the Pittsburgh Mandolin Society) owns. I played it for a minute. He played me 2 wonderful tunes.
Thats the extent of my Tenor experience. Advise, sources, experiences are welcome.
Reply With Quote
  #9  
Old 12-20-2011, 09:13 AM
Kitchen Guitars's Avatar
Kitchen Guitars Kitchen Guitars is offline
Formerly Yamaha Junkie
 
Join Date: Jun 2007
Location: South West Pennsylvania
Posts: 7,930
Default

Back is back together and cut! Skunk Stripes are in with minimal tear out. The wood is like 2 woods together! Some rock hard some like cruising through a Marshmallow.

Here is my oops. The router gide slipped and I didn't know till it was too late.

Here it is cleaned up and ready for the graft

I grafted in about a 1" wide strip. I have to look hard to see the boo boo.

Then 5 skunk stripes

I made the forms from scrap from building a chicken coop



The sides are bent. I didn't hear any cracking

Last edited by Kitchen Guitars; 12-20-2011 at 04:07 PM.
Reply With Quote
  #10  
Old 12-21-2011, 06:24 AM
Kitchen Guitars's Avatar
Kitchen Guitars Kitchen Guitars is offline
Formerly Yamaha Junkie
 
Join Date: Jun 2007
Location: South West Pennsylvania
Posts: 7,930
Default

Yea Haw. Yesterday was productive. I made nice straight Adi back braces. Radiused them and put in all but one. I ran out of fiberglass rods.
I made my Tailblock and the neck block. The sides REALLY want to go directions so I figure I gotta move to maintain shape. I took the spacers off the sides and had to gently squeeze it back to shape to install the blocks. IF the neck block is right it will be my first not having to redo. Fingers are crossed. I also made my neck blank. 2 layers of beautiful Quarter sawn Walnut with a rift sawn Oak center.
Today The top! Shape the neck. Order a Tailpeice and a set of friction tuners.
Told ya Neil I'm the morning guy. Not that sleepy thing you see when you get here for your 9pm shift
Reply With Quote
  #11  
Old 12-21-2011, 01:52 PM
Kitchen Guitars's Avatar
Kitchen Guitars Kitchen Guitars is offline
Formerly Yamaha Junkie
 
Join Date: Jun 2007
Location: South West Pennsylvania
Posts: 7,930
Default

Leapordwood wants to misbehave! I'm going to get the Kerfing on asap.


The new extension block and blade have turned my Bandsaw into a whole new tool! The neck took a few minutes to cut out. I love the Walnut!




Thinking about this for the headplate
Reply With Quote
  #12  
Old 12-21-2011, 02:29 PM
Neil K Walk Neil K Walk is offline
Registered User
 
Join Date: Aug 2006
Location: Pittsburgh suburbs
Posts: 8,309
Thumbs up

Wow, you work fast! I need to come over some morning. How long did that neck blank take?
__________________
(2006) Larrivee OM-03R, (2009) Martin D-16GT, (1998) Fender Am Std Ash Stratocaster, (2013) McKnight McUke, (1989) Kramer Striker ST600, a couple of DIY builds (2013, 2023)
Reply With Quote
  #13  
Old 12-21-2011, 02:47 PM
Kitchen Guitars's Avatar
Kitchen Guitars Kitchen Guitars is offline
Formerly Yamaha Junkie
 
Join Date: Jun 2007
Location: South West Pennsylvania
Posts: 7,930
Default

Quote:
Originally Posted by kwakatak View Post
Wow, you work fast! I need to come over some morning. How long did that neck blank take?
20 minutes to flatten the wood, Overnight glue up. 45 minutes tops on the cuts and round sanding the heel.
BTW If you like the look you are welcome to some of the walnut for your neck.
Reply With Quote
  #14  
Old 12-21-2011, 10:12 PM
Kitchen Guitars's Avatar
Kitchen Guitars Kitchen Guitars is offline
Formerly Yamaha Junkie
 
Join Date: Jun 2007
Location: South West Pennsylvania
Posts: 7,930
Default

Cut and installed the rossette. Sound hole. Made installed x braces. Made a fret board blank from a hunk of Gaboon. Got the back braces sized and ready. Just put in the rest of the Kerfing! Goooo night!
Reply With Quote
  #15  
Old 12-22-2011, 07:08 AM
Neil K Walk Neil K Walk is offline
Registered User
 
Join Date: Aug 2006
Location: Pittsburgh suburbs
Posts: 8,309
Default

Whoa. SLOW DOWN!
__________________
(2006) Larrivee OM-03R, (2009) Martin D-16GT, (1998) Fender Am Std Ash Stratocaster, (2013) McKnight McUke, (1989) Kramer Striker ST600, a couple of DIY builds (2013, 2023)
Reply With Quote
Reply

  The Acoustic Guitar Forum > General Acoustic Guitar and Amplification Discussion > Build and Repair

Thread Tools





All times are GMT -6. The time now is 09:51 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright ©2000 - 2022, The Acoustic Guitar Forum
vB Ad Management by =RedTyger=