#31
|
|||
|
|||
Got a little binding work done this week, not my favorite thing to do.
Used this Dremel set up with a dimmer to lower speed to cut a channel for the veneer strips rather an cut a rabbitt with binding machine. More of a see if it will work kind of thing. A little hard on the nerves. A few pics...back didn't come out as clean as the front, maybe some sanding and finish will help. Bruce, |
#32
|
|||
|
|||
I don't understand. You routed a purfling channel after binding was installed; or, you routed a purfling ledge then a binding ledge?
If the former, you won't be able to get a tight fit. Any gaps probably require a total binding/purfling redo or color matched gap filling. |
#33
|
|||
|
|||
I cut the channel after the bindings were installed. I had some gaps and cutting a channel this way cleaned up the gaps. I was just going to do a simple binding but didn't do a great job installing them thus the attempt to clean them up.
I need to get better at the binding thing so I don't have to come up with ways to clean up a screwup. Bruce, |
#34
|
|||
|
|||
It can be one of the harder things to get right. Not a lot of room for error.
__________________
Fred |
#35
|
|||
|
|||
Haven't posted in awhile, been in finishing hell, hard to escape from.
Had to run a few errands yesterday and found myself passing by Crosscut Hardwoods/Seattle. I stopped in to see if they had anything interesting(1st mistake), found a nice selection of q-sawn Padauk(2nd mistake.) I have a hard time resisting a nice piece of wood. Ended up with 2 nice Padauks and 2 fair SPCs, must be some kind of addiction thing. Did a few rough cuts to get the stuff down to workable sizes and will start the resaw this week. Not sure what the yield will be, depends on how good my resaw skills are. A few pics....The stuff looks a lot better than it photoed, really nice quatering. Last edited by BEJ; 03-20-2021 at 08:26 PM. |
#36
|
|||
|
|||
My main guitar, a classical I made in 1988, has padauk back and sides. A steel string that I'm taking forever to finish has padauk back, sides, neck and fingerboard.
Its a nice wood that can make a very nice guitar. Large pores, though, that are "fun" to fill. Left in the sun, padauk will eventually turn chocolate brown. My classical, which doesn't see much sun, is still only a light redish-brown color. |
#37
|
|||
|
|||
Just found this thread, interesting to tag along. I have this binding machine I bought from Blues Creek. It is great, although I still get nervous using it it has never failed me.
|
#38
|
|||
|
|||
I have just about the same set up, last change was switching to a Ridgit router, a nice little machine. Had some problems with climb cutting and have been making real small cuts with many passes since. Seems to be working better, a bit of a pain making so many passes but have been able to make continuous passes all the way around not changing direction. With light passes there has been no tear out so far.
|
#39
|
|||
|
|||
Quote:
|
#40
|
|||
|
|||
Cutting binding channels has been one of the things I've screwed up more than any other thing. You can read, watch videos, and other lessons but in the end you still have to make things work for you.
I think I've learned more by finding out not what to do than any thing else, you seem to remember a good screw up. We see the results of some of the really great builders on this site and sometimes how they do/did it. I sometimes wonder if their current methods are the same as when they started out or have evolved somewhat. Most likely some changes, but were they minor or did they have to make major changes to what they first thought would work. I think some of the aspects of building have a lot of leeway as to how to do it others not so much. Seems like finding out what and what you cannot do everyone has to discover for themselves, part of the journey. |
#41
|
|||
|
|||
Quote:
Just couldn't have all the nice material laying around doing nothing so I did 3 box builds. Guess I like building boxes more than guitars, hate binding, hate fretting, and maybe setting up too. But less so as the more I do it. A few pics of the latest boxes..... |
#42
|
|||
|
|||
Looking great! My first build a long time ago was padouk, a fabulous sounding tonewood at a very reasonable price. I imagine you already know this, but you need to seal it up right away and keep it out of the sun or the bright orange oxidizes to muddy brown really quickly. I even sealed up the inside of of the body before I closed the box.
|
#43
|
||||
|
||||
This place is just down the road from me. I haven't visited yet, but soon!
http://www.mcclellanwoodwork.com/ -Mike |
#44
|
|||
|
|||
The binding IMO is one of the hardest phases of the whole project. This jig from elevate lutherie tools has been a game changer for me.
here's the link https://elevatelutherie.com/tools/ |
#45
|
|||
|
|||
Quote:
__________________
http://victoryguitarshop.com/ |