#1
|
|||
|
|||
DIT Endpin jack reaming - What do I need?
I have a cheap Yamaha I want to install a soundhole pickup in. What tool(s) do I need to drill out the hole for the guitar cable jack? Is this an east thing to do myself or should I bring it somewhere?
thanks
__________________
Gear: PRS Hollowbody II Piezo, Martin HPL 000, PRS Angelus A60E, Martin 000-15M |
#2
|
|||
|
|||
The proper reamer is not a cheap tool - rather expensive for a one-time use. Drilling is a recipe for potential disaster unless you use a nice sharp Forstner bit and are very careful. Don't use a common twist drill bit. https://www.stewmac.com/Luthier_Tool...ck_Reamer.html
I would be tempted to take it to a shop and let them do only the drilling part. Then install the pickup and end pin jack yourself. Probably $20 or less for that work and a far smaller chance of problems. |
#3
|
|||
|
|||
A common tool to use is a step drill.
I usually use standard twist drills, starting with 1/8" or so, then increasing size a step or two at a time till you reach the desired size. I have a 'cello end pin reamer that is the right size to finish the job, but it isn't strictly necessary. Since it isn't a tapered end pin, you don't really need a tapered hole (i.e. a tapered reamer). |
#4
|
||||
|
||||
I do use a twist drill for this job. The trick is to do it in a drill press. I turn the table near 90 degrees and clamp the guitar to the table with the headstock solid against the “ground” which I adjust the height of with books. I’ve done this many times w/o mishap, but only with really expensive guitars .
|
#5
|
|||
|
|||
Is the hole just a screw hole from the end pin or is it a large tapered end pin hole? I would not recommend twist drills for a larger hole. I've had a disaster doing that many years ago when I got into this and vowed never to do it again. Maybe it's pore technique on my part but I've never had a problem with a step bit and would feel comfortable using that on the most expensive of guitars.
|
#6
|
|||
|
|||
I use a Forstner bit in a battery hand drill.
I've done several of these, and it's usually where there's already some sort of hole there already. I plug the hole by gluing in a short piece of dowel rod so the Forstner bit has a proper place to start the point. I cover the end of the instrument with masking tape before drilling the hole. Once a Forstner bit starts properly there's no need for the center point, so the section of dowel that's glued in doesn't need to be very long. |
#7
|
|||
|
|||
Whilst some people possess the skills to drill an end pin hole with a drill, I am not one of those that endorse it, use a step drill or reamer, twist drills have far too much associated risk of tearing the sides out.
Steve
__________________
Cole Clark Fat Lady Gretsch Electromatic Martin CEO7 Maton Messiah Taylor 814CE |
#8
|
|||
|
|||
Is the standard size for the hole 1/2” in diameter?
__________________
Gear: PRS Hollowbody II Piezo, Martin HPL 000, PRS Angelus A60E, Martin 000-15M |
#9
|
|||
|
|||
You're going to get the usual argument, but 1/2" Forstner bit is what I've always used. (TONS of installs have been done using a 1/2" hole with no problems.)
K&K has sold more than a few pickups and a 1/2" Forstner is recommended in their installation instructions. (... wait a bit for the counter-point!) |
#10
|
|||
|
|||
What's your jack diameter? What do installation instructions recommend?
|
#11
|
|||
|
|||
Most likely the diameter is 15/32. As Rudy stated there are thousands of guitars out there with 1/2in holes and they are just fine. Ideally you would want a perfect fit and you can easily find a 15/32 drill bit but don't sweat it if all you have is 1/2, as you stated, it's a cheap Yamaha.
|
#12
|
|||
|
|||
I’d try it yourself. Cheap instruments are perfect for practicing technique. Make sure the drill speed matches the hole. I *think* you want 3000rpm but it’d be good to check. I could tell you how I know but then ...:
|