The Acoustic Guitar Forum

Go Back   The Acoustic Guitar Forum > General Acoustic Guitar and Amplification Discussion > Custom Shop

Reply
 
Thread Tools
  #1  
Old 05-03-2021, 02:42 AM
JazzyJ JazzyJ is offline
Registered User
 
Join Date: Oct 2009
Posts: 64
Default Custom (Rubber/Silicone) Soundhole Cover / Feedback Buster?

Hi, is anyone aware of a place that can make custom feedback busters in rubber/silicone?

A regular 4" cover is too big for my Yairi DY75 so I'm looking for something smaller - and with a cut out for volume dial!

I really don't like the wooden designs from the likes of Lutehole.com and lacuna-acousticart.com (a bit medieval for me!) - I'm just looking for something plain and black like all of the regular ones that are available for standard 4" holes.

Perhaps it can be done with 3D printing nowadays?

Failing that, is it possible to 'sand off' an exisiting rubber one (by 2 or 3mm) to get it to fit?

Or is the reality for me a can of black paint, a CD, some hot water, a pair of scissors, a bit of foam and a glue gun my best option.......

Thanks for any suggestions or advice anyone can offer (apart from playing at a lower volume!).
Reply With Quote
  #2  
Old 05-03-2021, 07:34 AM
Tim McKnight's Avatar
Tim McKnight Tim McKnight is offline
AGF Sponsor
 
Join Date: Oct 2005
Location: Morral, Ohio
Posts: 5,514
Default

If you are wanting to try a DYI, a balloon and margarine bowl lid will work, which is easily cut with scissors. I doubt you could sand the rubber cover to fit but you should be able to trim it with some HD scissors.
__________________
tim...
www.mcknightguitars.com
Reply With Quote
  #3  
Old 05-03-2021, 08:29 AM
tadol tadol is offline
Registered User
 
Join Date: Aug 2008
Location: Berkeley, CA
Posts: 4,407
Default

Know anyone with a 3d printer?
__________________
More than a few Santa Cruz’s, a few Sexauers, a Patterson, a Larrivee, a Cumpiano, and a Klepper!!
Check out my podcasts -
https://youtu.be/xlFHEjl2hPA
https://youtu.be/8SlNukuRU0U
https://youtu.be/YGeFUD1Rmeo
Reply With Quote
  #4  
Old 05-03-2021, 08:37 AM
Alan Carruth Alan Carruth is offline
Registered User
 
Join Date: Feb 2011
Posts: 3,505
Default

I've made sound hole covers using foam poster board and card stock. Cut the foam board to a snug fit, and then glue it to a larger disc of card stock to keep it from falling in. This is a jury rig for experimental purposes, of course, but you could readily adapt that to nicer materials such as wood, and cork, or felt, for gaskets.

The lute rose type of feedback buster works by adding drag to the air flow through the hole at the 'main air' resonant pitch, which is the usual problem. Having a network of holes that cover the entire span of the hole, with a lot of edges, is the key to cutting down the amplitude of the mode without altering it's pitch much. A piece of window screen or gauze stretched over a ring would be extremely effective. The 'inverted wedding cake' parchment roses are the paradigm.

If there's a maker space near you it might be possible to get somebody there to make one up on a laser cutter, or you could join and do it yourself.
Reply With Quote
Reply

  The Acoustic Guitar Forum > General Acoustic Guitar and Amplification Discussion > Custom Shop

Thread Tools





All times are GMT -6. The time now is 05:39 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
Copyright ©2000 - 2021, The Acoustic Guitar Forum
vB Ad Management by =RedTyger=