#1
|
|||
|
|||
broke the high E string
I’m new to electric guitar. I’m an acoustic player, used to mediums on my dreads. Today I broke the high E string while practicing some licks that have a whole step bend (from C to D, to give you an idea where I want bending). The string were pretty new. I believe they were 9’s. Felt pretty skimpy compared the the 13’s on my dreads. So I guess I am not surprised it snapped but the strings weren’t old or worn out. Or could I have been doing something wrong in my newbie way of bending the high E string?
|
#2
|
|||
|
|||
Some strat bridges have very sharp edges on the block and the bridge plate that make strings more likely to break. Check the hole where the string goes through the bridge for sharp edges, assuming it's a strat and the string broke near the bridge. If that is the case, a small file will do the trick to smooth off the edge and your strings will last longer.
__________________
As my username suggests, huge fan of Yamaha products. Own many acoustic-electric models from 2009-present and a couple electric. Lots of PA too. |
#3
|
|||
|
|||
Quote:
Actually, it snapped somewhere around the 15th fret. Should’ve mentioned that in the original post. And yes. It’s a strat. |
#4
|
|||
|
|||
SIT strings sells their set of 9s with a spare 9. May not be a bad idea to grab a few singles next time you're at a music store. Or just go with something a bit heavier.
__________________
As my username suggests, huge fan of Yamaha products. Own many acoustic-electric models from 2009-present and a couple electric. Lots of PA too. |
#5
|
|||
|
|||
Are the frets smooth in that area?
__________________
Breedlove, Landola, a couple of electrics, and a guitar-shaped-object |
#6
|
|||
|
|||
Good point. Yes the frets are smooth but maybe in my newbie way, I am pressing down too hard. Will have to see if it happens again after I restring. |
#7
|
|||
|
|||
What brand of strings were you using?
__________________
Mike My music: https://mikebirchmusic.bandcamp.com 2020 Taylor 324ceBE 2017 Taylor 114ce-N 2012 Taylor 310ce 2011 Fender CD140SCE Ibanez 12 string a/e 73(?) Epiphone 6830E 6 string 72 Fender Telecaster Epiphone Dot Studio Epiphone LP Jr Chinese Strat clone Kala baritone ukulele Seagull 'Merlin' Washburn Mandolin Luna 'tatoo' a/e ukulele antique banjolin Squire J bass |
#8
|
|||
|
|||
Something else I should’ve mentioned earlier. I just got it and the shop set it up so I am not sure. But I was told it was a 9. |
#9
|
|||
|
|||
I broke a couple of high E strings when I got out the electric after not playing it for ten years. I have trouble with that bend. Especially on the 10th fret. I tend to slide that one.
|
#10
|
|||
|
|||
If they did a setup, and used the same set of strings start to finish, that would be enough to make the strings -- especially the high e -- more likely to break. All that tuning up/retuning does a number on the strings. When I do setups, I usually throw a fresh set of strings on when I'm done just to ensure I'll be able to play that set awhile.
__________________
As my username suggests, huge fan of Yamaha products. Own many acoustic-electric models from 2009-present and a couple electric. Lots of PA too. |
#11
|
|||
|
|||
I can't recall a need to bend the high end E string. (Higher string tension than the strings above it which makes it more difficult to bend for a start which could explain things for you).
|
#12
|
|||
|
|||
Quote:
It was lick #1 from here https://youtu.be/Gu2esZ-PzFM |
#13
|
|||
|
|||
Quote:
Good luck! Last edited by Steel and wood; 06-14-2019 at 08:04 PM. |
#14
|
|||
|
|||
Quote:
Yes. It was a bit of a fight bending the high E. I just changed my strings. Gonna go back at it and see if I can break the string again |
#15
|
|||
|
|||
That's actually a kind of odd place for the string to break; they usually break at one of the stress points...saddle, sustain block, nut, etc. It could have simply been a defective string or maybe it got kinked during installation.
Another thing...unless your bridge is really, really decked (or a hardtail), bending a string a whole step will cause the bridge to pull up, forcing you to bend the string just that much more in order to arrive at the intended pitch. If I have a bend like that, sometimes I palm the bridge (if possible) to hold it down while bending with fingers. My bridges are set up for mostly dive with very slight up-trem...floating just a bit. I mainly do it this way so the bridge doesn't smack the top of the guitar if I let go of the arm.
__________________
Larrivee L-10 Custom Larrivee DV-10K Larrivee L-03 Taylor 412K ('96) Yamaha LL16-12 (SOLD) PRS 'Studio' (SOLD) Rickenbacker 660-12 (SOLD) Fender USA Deluxe Strat Fender USA Roadhouse Strat Fender MIM/USA Partscaster Fender MIM Nashville Tele Kelsey Custom Hardtail Strat Fender MIM P-Bass |