The Acoustic Guitar Forum

Go Back   The Acoustic Guitar Forum > General Acoustic Guitar and Amplification Discussion > Acoustic Amplification

Reply
 
Thread Tools
  #1  
Old 03-14-2020, 05:01 PM
Awagner Awagner is offline
Registered User
 
Join Date: Feb 2013
Posts: 4
Default Pickup Advice

I have a vintage Guild 12-string that has a stock volume and tone knob. I upgraded the original pickup system with an LR Baggs Element that my guy was able to connect to the knobs so they function as intended. Consequently, the soundhole volume control was not installed. The problem is that although it works ok, the sound quality is not that great, and the output is weak.

I want to install a high quality system that will utilize the original knobs. Either volume and tone, or maybe even a blended system where one knob blends the mic and pickup and the other controls the volume.

Maintaining the use of the stock knobs is essential.

Any suggestions?

Thanks.
Reply With Quote
  #2  
Old 03-15-2020, 05:49 AM
pieterh pieterh is offline
Registered User
 
Join Date: Oct 2010
Location: Near Stockholm, Sweden
Posts: 3,467
Default Pickup Advice

Do you have onboard amplification connected to the knobs or are they passive? Ie is the tone knob similar to an electric guitar tone control in that it rolls off treble? Does the guitar require a battery? How are you amplifying, acoustic amp, powered speaker or direct to a mixer and PA?

I suspect the system is passive as you say the signal is weak, in which case you have two basic options if you want to retain the onboard knobs, depending on what you are using as amplification:

1. Invest in a good active (battery or phantom powered) direct box. This is a good option if you are connecting directly to a mixer and PA. By balancing and optimising the impedance of the signal it makes it much easier to gain up and eq at the mixing desk. Active is recommended as a passive direct box will give a good signal to a mixing desk at the expense of the line out to your own amplifier if using one.

2. Invest in a good floor- or even rackmount preamp. I have a 12-string with a passive Baggs iBeam pickup which is fairly useless without my Tonebone Pz-pre floor preamp. The signal is too weak and thin sounding on its own - itís no K&K Pure Mini! With the preamp I have control over signal level to a mixer, powered speaker or amplifier, plus it has built in direct out so sound engineers are happy.
__________________
Gibson ES-335 Studio 2016; Furch OM34sr 2015; Fender MiJ Geddy Lee Jazz bass, 2009; Taylor 414CE 2005; Guild D35 NT 1976; Fender MIM Classic 60s Tele 2008; Fender US Standard Strat 1992; G&L ASAT classic hollowbody 2005; Ibanez RG350MDX 2010(?); Ibanez Musician fretless, 1980s; Seymour Duncan Tube 84-40; Vox AC4TV;

Ex-pat Brit in Sweden
Reply With Quote
  #3  
Old 03-15-2020, 10:05 AM
Awagner Awagner is offline
Registered User
 
Join Date: Feb 2013
Posts: 4
Default

The Element system is active, and comes with a battery pack, which was installed.

When I say the output is weak, I mean that when I switch from any of my other guitars to this one, the volume is lower, and I need to increase it a bit to get it to the same level as it was before. Not a real problem, just an observation. The real issue for me is the quality of the amplified sound. It is muddy.

I plug into a Fishman Loudbox Artist or Fishman SA330X, and I just acquired a T-Rex Soulmate Acoustic.

The guitar is a Guild 12 string from 1983. I donít know how the tone knob functions. I donít really use it, and it does very little to modify the sound.

Here is a picture.




I think the issue is that the Element system was modified so that it works with the stock knobs, but I am looking for a better solution.
Reply With Quote
  #4  
Old 03-15-2020, 10:36 AM
pieterh pieterh is offline
Registered User
 
Join Date: Oct 2010
Location: Near Stockholm, Sweden
Posts: 3,467
Default

I wonder if it is the controls that are getting in the way of the sound youíre after. It wouldnít surprise me if they were designed for a passive system and that they arenít the ideal controls for the Element.

Maybe new controls that fit the existing holes, or maybe just bypass them completely and use the Element with the sound hole controls it came with...
__________________
Gibson ES-335 Studio 2016; Furch OM34sr 2015; Fender MiJ Geddy Lee Jazz bass, 2009; Taylor 414CE 2005; Guild D35 NT 1976; Fender MIM Classic 60s Tele 2008; Fender US Standard Strat 1992; G&L ASAT classic hollowbody 2005; Ibanez RG350MDX 2010(?); Ibanez Musician fretless, 1980s; Seymour Duncan Tube 84-40; Vox AC4TV;

Ex-pat Brit in Sweden
Reply With Quote
  #5  
Old 03-15-2020, 10:53 AM
Awagner Awagner is offline
Registered User
 
Join Date: Feb 2013
Posts: 4
Default

I could have installed the Element or any other good system and bypassed the controls to achieve better sound, but I really prefer to use the original control knobs as intended.

Not sure there is a viable solution, but I hope so.

Thanks for your feedback.
Reply With Quote
  #6  
Old 03-15-2020, 11:42 AM
jseth jseth is offline
Charter Member
 
Join Date: Dec 2008
Location: Oregon... "Heart of the Valley"...
Posts: 9,632
Default

I would be very surprised if those knobs are, indeed, "original"... don't recall any older Guild with something like that. Maybe they were there when you got the guitar, but are not factory-original?

Of course, if you have owned it since it was new, then I'm obviously way off base!

When you changed to the Element system, did your tech use the existing vol/tone pots are did he use the Baggs versions and just connect them to the knobs? If the pots are what were in the guitar, they may be a big part of the problem.

Sounds as though you are more committed to the knobs than the sound of the guitar....

Hope you find a solution that works for you...
__________________
"Statistics are one of the most limiting sources of information ever devised by man.
Our job is to do the impossible; we don't need to hear that it can't be done..."
Reply With Quote
  #7  
Old 03-15-2020, 11:59 AM
SpruceTop SpruceTop is offline
Charter Member
 
Join Date: Jan 2006
Location: Rochester, New York
Posts: 9,134
Default

Here's Tim Gregg from Presley's Country Jubilee on RFD-TV. His Guild has the two knobs but they're arranged 90-degrees from the Guild in the OP's photo. If it's not a Guild-installed pickup/preamp, maybe Tim had the same or similar aftermarket system as the OP added to his Guild with the preamp knob orientation to his liking?

__________________
Martin HD-28 Sunburst
Martin D-18
Guild F-212XL STD
Adamas I 2087GT-8
Huss & Dalton TD-R
Taylor 717e
Taylor 618e
Taylor 614ce
Taylor 322ce
Larrivee D-40R Legacy
Larrivee D-40M Legacy
Larrivee C-03R TE Tommy Emmanuel
Emerald X20
Takamine EF360S-TT/TLD-2
Ovation Elite Plus
Yamaha LL-TA TransAcoustic
Republic Duolian/Schatten NR-2

Last edited by SpruceTop; 03-15-2020 at 12:11 PM.
Reply With Quote
  #8  
Old 03-15-2020, 01:07 PM
Awagner Awagner is offline
Registered User
 
Join Date: Feb 2013
Posts: 4
Default

Quote:
Originally Posted by jseth View Post
I would be very surprised if those knobs are, indeed, "original"... don't recall any older Guild with something like that. Maybe they were there when you got the guitar, but are not factory-original?

Of course, if you have owned it since it was new, then I'm obviously way off base!

When you changed to the Element system, did your tech use the existing vol/tone pots are did he use the Baggs versions and just connect them to the knobs? If the pots are what were in the guitar, they may be a big part of the problem.

Sounds as though you are more committed to the knobs than the sound of the guitar....

Hope you find a solution that works for you...
It is a pretty rare model. A 1983 D70-12E. The E is for electronic (or electric), and I confirmed with Hans Moust that the knobs and the original system are original to the guitar.

The pots were replaced when my tech undertook the project, but I would have to find out from him exactly what he did.

I have no problem replacing the system with another that sounds better, if there is no other option, but my preference is not to make the knobs obsolete.

I just want to determine if what I want to do is possible, so that the guitar can be played as intended.

Thanks.

Last edited by Awagner; 03-15-2020 at 01:24 PM.
Reply With Quote
Reply

  The Acoustic Guitar Forum > General Acoustic Guitar and Amplification Discussion > Acoustic Amplification

Thread Tools





All times are GMT -6. The time now is 12:32 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
Copyright ©2000 - 2021, The Acoustic Guitar Forum
vB Ad Management by =RedTyger=