#46
|
|||
|
|||
Quote:
Powered Ginger Root mixed with water might work, but I wouldn't want to risk having liquid run out my jackhole in the middle of playing in front of 20 people........ talk about embarrassment.
__________________
2007 Squire HelloKitty named "Pinky" |
#47
|
||||
|
||||
This thread is as fun as the one on how not to remove the pick guard but not as much fun as the thread on how to convert a Venetian cutaway into a Florentine cutaway.
__________________
“Reason is itself a matter of faith. It is an act of faith to assert that our thoughts have any relation to reality at all.” ― G.K. Chesterton |
#48
|
|||
|
|||
Quote:
@ TT You would be waiting quite a while for that soldering iron to heat up.
__________________
Instruments I own. 2004 Martin DC16 GTE Custom (1 & 13/16" nut) w/ Fishman Prefix Stereo Onboard Blender 1999 BC Rich Warlock N.J. Series (import) 2009 Lanikai LU21 Dunlop shaker egg Alesis DM10 Pro |
#49
|
|||
|
|||
I'm not sure I understand the powdered ginger connection. Does it act as a catalyst or lubricant?
__________________
Steve |
#50
|
|||
|
|||
Link please!
__________________
Instruments I own. 2004 Martin DC16 GTE Custom (1 & 13/16" nut) w/ Fishman Prefix Stereo Onboard Blender 1999 BC Rich Warlock N.J. Series (import) 2009 Lanikai LU21 Dunlop shaker egg Alesis DM10 Pro |
#51
|
||||
|
||||
I think you you rub it fast enough, you might come up with a solution.
|
#52
|
|||
|
|||
Yes, it does.
|
#53
|
|||
|
|||
I'd be worried that I'd never get the jack off again after using the ginger. The soldering iron in the end pin hole is the way to go... very effective, but not for the feint of heart.
|
#54
|
||||
|
||||
I looked but could not find it. There were lots of helpful hints and one poor soul that just did not get that it was a joke and kept pleading for the OP not to try it.
It was in open mic, so I think it just went off to electron oblivian. What a shame. I'm going to have a moment of silence. Please join me. Maybe I should just start another one.
__________________
“Reason is itself a matter of faith. It is an act of faith to assert that our thoughts have any relation to reality at all.” ― G.K. Chesterton |
#55
|
|||
|
|||
It certainly does...
It helps protect your guitar when you stand it up against the wall... It sits on the strap knob and stops it from scratching the bottom of the guitar....It works too.... I've personally damaged dozens of guitars using this method,but not one of them has had any damage to the strap on end pin.. One way to repair the plug is to take it out of the body and screw a thread on the end of it,then you can put it back in ,and by using two nuts (same size as the plug) you can reach inside the body and tighten up the nuts. The second nut locks the first one in place.. Exercise caution if doing this method though,once,I got my whole arm stuck in the body,and had to go to the E.R to have it removed..I suffered a few minor grazes,but I'm happy to say there was zero damage to the strap on pin.. Bat
__________________
72 rickenbacker 330 88 fender strat 80's yasuma 250b martin d16 big baby(my wifes) vox amp Epi ej200 Blueridge BR163 Blueridge BR73 |
#56
|
|||
|
|||
No way I'd ever go elbow deep and risk getting stuck......
|
#57
|
|||
|
|||
I just don't know about the hot iron thing. With all the different approaches -hot, cold, wrapped, unwrapped, liquid or powder - risky!
I bet there are luthier associations, or woodworking groups that could offer some guidance. Maybe you could find a branch that would collaborate on the project. I am just concerned that if things are done without the proper training you might wind up with all these small circular scars that would then cause you to have to sand the box, or lead to even more complex sergury. Hard to believe but sometimes the simplest things turn into quite a mess. |
#58
|
|||
|
|||
In my years as a boat builder I have found it is not uncommon to find the need to ream the hole to accommodate a larger bung plug...now, these bung plugs serve only one purpose....to fill the void.
I would assume the same is true for a guitar, no? That said, once the sides of the bung hole have become worn and tattered the only recourse is to ream that baby out for a larger bung plug which can then be inserted with a minimum of upward driving force ..heat from friction alone will suffice to make a smooth insertion. I have no idea what this ginger root thing is all about....a little spiddle works fine for me...call me "old fashioned"...
__________________
Barrett |
#59
|
|||
|
|||
I just got done checking mine and I noticed after years of playing with a strap on, I have discoloration around the end hole, probably caused by sweat and never cleaned properly. This isn't my main unit, rather it is my beater that I also let friends use, or who ever shows up so over the years it has seen a lot of action. I tried several kinds of cleaner, but nothing will touch the discoloration. I wonder if there is any kind of bleach especially made for removing stains in that area.
|
#60
|
|||
|
|||
Quote:
I think I'd test it out first, though. The foaming, stinging action is normal...btw..
__________________
Barrett |