New IR pedal from AMT

[Cuki79]

It's a small tunable FX pedal. (Not as powerfull as a HX stomp but smaller)



AMT U-2 Pangaea Ultima Brain Frame.

The device is a hardware platform on the basis of which various guitar effects can be implemented in software. Changing the functionality of the device is carried out by changing the “firmware” of the device.


FIRMWARE TYPES
there are available for downloading the next Firmware for the AMT Pangaea U-2 Ultima:

01 – IR CabSim Fx
The main firmware comes with the device by default.
A feature is an analog-digital preamp section with three channels: clean, low & high gain.

TUNER;
METRONOME;
[NG] Noise Gate – Global settings / by each preset);
[CM] Compressor;
[PR] Preamp – analog-digital preamp section (Clean / Drive Low / Drive High);
[PA] PowerAmp – 9 types of virtual Power Amps;
[IR] CabSim – 1 WAV IR for both L/R channels per preset; IR/Dry parameter for mixing the processed and Dry signal;
[EQ] Equalizer – parametric Pre/Post EQ;
[FT] Filters – Hi/Low pass filters + Presence;
[FX] DL/RV – Delay or Reverb per preset
+ rich switching capabilities (2-Preamps Bricks Mode, up to 2 external 2-button Footswitches, Expression pedal, MIDI, etc.)

02 – Modulation FX
The firmware that turns “Ultima” into an effects processor is designed for the case when your Pedalboard, which already has preamp/distortion pedals, requires expanding the sound palette due to various modulation effects.

Noise Gate (global setting)
Compressor
Resonance Filter (wah-wah etc.)
Flanger
Chorus
Delay
Tremolo
+ other features

03 – IR Stereo CabSim
The firmware that turns the device into a powerful stereo IR impulse responses cabinet emulator.

IR Stereo cabsim (2 IR’s per preset: the first wav IR for the LEFT channel, another one wav IR – for the RIGHT channel)
Parametric Pre/Post EQ
Hi/Low pass filters + Presence

04 – Stereo Delay
Multifunctional STEREO IN/OUT Delay effect.

05 – Stereo Reverb
Multifunctional STEREO IN/OUT Reverb with the following types:

Gold Reverb
Hall
Room
Plate
Spring
Gate
Reverse

06 – Pre/Post FX
The firmware that turns the Ultima U-2 device to the PRE / POST effect processor.

PRE section:

Noise Gate (global setting)
Compressor
Phaser
Resonance Filter (wah-wah etc.)
Flanger
POST section:

IR cabsim (1 IR for both L/R channels per preset)
Parametric Pre/Post EQ
Hi/Low pass filters + Presence
Delay or Reverb effect per preset
+ other features

SPECIFICATIONS
IN L, IN R – Inputs of the Left and Right channels:
– input impedance 470 kОм
– rated input voltage of audio signal 0.316Vrms (-10dBV)
– maximum sinusoidal voltage 2.5V (+8dBV)

AUX IN
– Input impedance 2kOhm
– maximum sinusoidal voltage 0.85V (-1.4dBV)

OUT L, OUT_R – Outputs of the Left and Right channels:
– output impedance 1,5kOhm (unbalanced output)
– maximum sinusoidal voltage 2,6V (unbalanced output)
– phantom power protection – present

PHONES – Output to headphones:
– minimum headphone impedance 32 Ohm
– maximum output sinusoidal voltage (no load) 2,6V (8dBV)
– output impedance 12 Ohm

POWER
– Voltage DC 12V
– Current consumption Approx. 300mA

CHARACTERISTICS OF IR FILES
– Type: WAV, IR A/D – D/A converters 24 bit
– Sampling frequency: 48 kHz
– IR length: 1024 samples (21.3 msec)

– S/N: 115dB.
– Latency: 1.2 ms / 0.0012 s
– Codec: AD\DA AK4621

DIMENSION (HxWxD) 47mm x 55mm x 95mm

WEIGHT 270 g (without package)