#1
|
|||
|
|||
Installing an arm rest
Hello all,
I was looking to see if anyone has any experience using aftermarket arm rests. I wanted to possibly install one on my Taylor GC8E, but didn't want to do it without getting some opinions first. Especially with the possible damage to the finish if the risk exists. Thanks! |
#2
|
|||
|
|||
Lots of posts to search on AGF for this topic. In short, many of us use the John Pearse Ebony arm rests. Few members have reported problems with damaged finishes. I can recall only one. I have installed and removed the same arm rests several times. In fact, the arm rest have out lasted several of my fleeting guitar romances. I have installed on Martin and Taylor without issue. Taylor finish is especially strong.
__________________
"Lift your head and smile at trouble. You'll find happiness someday." |
#3
|
|||
|
|||
Quote:
|
#4
|
|||
|
|||
Installing an arm rest
Quote:
I use the same 3M VHB tape they use. A roll is a lot cheaper. I cut it to size. I also don't use a full line of tape. I use about 2/3 coverage.
__________________
"Lift your head and smile at trouble. You'll find happiness someday." |
#5
|
||||
|
||||
Just installed the John Pearce ebony slimline on my Martin MMV and I am happy with the outcome. First, it's real easy; second, it's comfortable and third, I have noticed a better tonal response when fingerpicking.
__________________
RonSenf 2023 Taylor AD22e 2001 Guild F47RCE Certified Fretting Technician - Galloup School of Luthiery 2005 Guitar Builder/Tech |
#6
|
|||
|
|||
Quote:
Thanks
__________________
"To sit home, read one's favorite paper, and scoff at the misdeeds of the men who do things is easy, but it is markedly ineffective. It is what evil men count upon the good men's doing." T.Roosevelt |
#7
|
|||
|
|||
Quote:
Don't know the product number. And, can't remember where I got it. Probably amazon.com.
__________________
"Lift your head and smile at trouble. You'll find happiness someday." |
#8
|
|||
|
|||
Identiferent, the John Pearse armrests that I use and endorse are easy to install. Looking at a picture of the Taylor GC8E, the armrest that I would probably choose for that guitar would be the Slimline model:
John Pearse Slimline Armrest What you should do to be certain, though, is go to the Breezy Ridge/John Pearse website and print out the templates of the different armrest models to see which best match the curvature of your guitar's lower bout: http://jpstrings.com/armrest.htm#Armrest-n http://www.jpstrings.com/ftp/AR-scansht.pdf Once you determine which armrest to get and it arrives, the way I prepare to install them is to first lay the armrest on the guitar top and position it where I think it looks best. Using low tack painter's masking tape, I also stick it on temporarily so I can pick up and play the guitar, in order to make certain that the armrest is in a comfortable spot for my forearm, as well as matching the curvature of the lower bout. What I've discovered is that on larger guitars like Martin dreadnoughts and Gibson slope-shouldered dreadnoughts, even though I play right-handed the right-handed Original design armrest isn't in the best spot for me, because my right arm crosses the guitar body a bit lower than the armrest is designed for. So on those guitars I actually use a left-handed armrest. Anyway, once I figure out where I want the armrest to go, I put strips of the painter's masking tape on the top at each end of where I've positioned the armrest. Then I remove the backing on the adhesive strip of the armrest, and quickly but accurately press it into place. Then I remove the positioning strips of masking tape, and I'm done. As for the possibility of finish damage, on a modern Taylor guitar the possibility is remote to nonexistent. The UV-cured polyester finish that Taylor uses is one of the most durable in production use. I've installed and removed armrests multiple times on poly-UV finished guitars, and never had the slightest problem or finish damage. John always cautioned me that his armrests were designed for modern guitar finishes in good condition, not for antique guitars with brittle, cracked or "window pane" checked finishes. There isn't any problem applying a Pearse armrest to any of those finishes, but should you ever decide to remove the armrest the adhesive strip theoretically could bring some flakes of that old finish up with it. But a modern Taylor guitar is at no risk for this. I imagine that if you were to drop high explosives onto the guitar, or perhaps torment it with a propane torch, you might damage the finish. But aside from actual military ordinance, the finish Taylor uses is what's often called "bomb-proof." It certainly won't be damaged by sticking a John Pearse armrest onto it. Hope this helps. Wade Hampton Miller |
#9
|
|||
|
|||
The only really serious armrest that works on all my guitars is the one developed by Andreas Abel. It is so well designed and so comfortable! Like a chin rest on a Stradivarius.
And you put it on and off in literally a couple of seconds. Here on my Poljakoff: |
#10
|
|||
|
|||
Thanks for all the advice everyone. I'll look at these and see what I order! I'm always cautious about doing anything with the Taylor, as cost me a pretty penny. Thanks again!
|
#11
|
||||
|
||||
Wade is an expert on this so he already gave you the advice you need.
I am just confirming his suspicion that the slimline is best for you. I have a Taylor Grand Concert and that is the size that worked best and looks great installed (nicely matches the contour of the body.
__________________
Fazool "The wand chooses the wizard, Mr. Potter" Taylor GC7, GA3-12, SB2-C, SB2-Cp...... Ibanez AVC-11MHx , AC-240 |
#12
|
|||
|
|||
Quote:
I actually switched to slimlines for my dreads too. I think that's a very nice shape.
__________________
"Lift your head and smile at trouble. You'll find happiness someday." |
#13
|
|||
|
|||
Quote:
whm |
#14
|
|||
|
|||
Great deal on the grey tape on Amazon tonight. 1/2 inch wide so I'll have to cut it but the price for the narrow stuff (only in black) was very high.
|
#15
|
|||
|
|||
I don't care if 100% report no damage from gluing these things on.
What's the longest anyone could have had one of these things glued on? And was it glued on with the exact same glue used today? I'm super conservative when it comes to what even remotely might damage the finish of my nice guitars over the very long term. In a century or two I'll check; if everyone has zero damage to their nitro celulose finishes I might consider gluing an armrest to my guitars. |