#16
|
|||
|
|||
I did something very similar and have probably 10 guitars on it so far.
|
#17
|
||||
|
||||
Here are the sizes of the dumb bells I made. The main three are 28mm for the binding, 25mm for the bottom purfling, and 21 for the top purfling. When I use abalone which is a bit shallower I use 24mm and 30mm also. I'll fine tune the diameter with a wrap of binding tape on the dumb bells as needed.
__________________
Mark Hatcher www.hatcherguitars.com “"A conclusion is the place where you got tired of thinking". Steven Wright |
#18
|
|||
|
|||
Interesting. Building jigs can be fun. I may try this.
__________________
(2006) Larrivee OM-03R, (2009) Martin D-16GT, (1998) Fender Am Std Ash Stratocaster, (2013) McKnight McUke, (1989) Kramer Striker ST600, a couple of DIY builds (2013, 2023) |
#19
|
|||
|
|||
I’ve been hunting for parts and am finding precious little locally to make different sized dumbbells. Yours looks to be adjustable. Are you using locking washers to keep the guide from working loose while the router is running?
__________________
(2006) Larrivee OM-03R, (2009) Martin D-16GT, (1998) Fender Am Std Ash Stratocaster, (2013) McKnight McUke, (1989) Kramer Striker ST600, a couple of DIY builds (2013, 2023) |
#20
|
|||
|
|||
Quote:
There is a threaded insert in the adjustable block and I routed out a slot so it can slide up and down. In this pic you see a dovetail slot but it's actually routed through. It's the only pic I could find but illustrates the point. This is the old version again but just to show that there is a threaded knob that goes through the back of the board into the threaded insert of the adjustable block to lock it down tight. I think maybe I did add a lock washer to it but it's probably not even necessary. Last edited by redir; 06-13-2019 at 07:43 AM. |
#21
|
|||
|
|||
@redir, that second picture didn't come through. I like your idea about just rounding off the plywood guide block. Finding components is nearly as difficult as it is justifying buying all the expensive jigs from StewMac and LMI.
That being said, I got something workable put together. I haven't tested it yet though. I went with a 1/4" x 2" tension rod with 1/4" (inner diameter) x 3/8" (out diameter) x 1.4" wide nylon washers. I need to figure out a way for it to stay put in that groove but otherwise everything is aligned. I'm going to try to drill a hole through the guide black to thread a 3" x 3/8" steel sheet metal screw through and into the slot in the tension rod of the dumbbell. If it doesn't work, I've always got more plywood and threaded inserts. PS: pay no attention to the laminate trimmer I have mounted to it. It's a $30 cheapie from Harbor Freight. I'm on a shoestring budget. The jig cost me less than $20 to make. The router bits cost more.
__________________
(2006) Larrivee OM-03R, (2009) Martin D-16GT, (1998) Fender Am Std Ash Stratocaster, (2013) McKnight McUke, (1989) Kramer Striker ST600, a couple of DIY builds (2013, 2023) |
#22
|
|||
|
|||
Is a down cut bit important? I see them at Stewmac and LMI but they both have an extension for a bearing and I think that might not work with this design.
__________________
Fred |
#23
|
|||
|
|||
[QUOTE=redir;5713223]I did something very similar and have probably 10 guitars on it so far.
So Redir, it appears that yours has a fixed 'dumbell' and the foot that it mounts to is adjustable - which seems like a more logical design than changing the dumbell for every different cut or setup.
__________________
______________ ---Tom H --- |
#24
|
|||
|
|||
I tried updating that second pic.
I think the advantage of using dumbells that are interchangeable is that you can move along more quickly and perhaps make the the whole jig a lot stiffer which may make it more accurate. But of course you have to have specified depths of binding which for the most part I almost always do but my purfling schemes differ a lot so I like the fine adjustments. Neil you will want some kind of doughnut though for sure. |
#25
|
|||
|
|||
EDIT: re-read the entire thread and found this post redundant.
Last edited by charles Tauber; 06-13-2019 at 08:38 PM. |
#26
|
|||
|
|||
I see some people use metal flanges for the donut but there are also rounded nylon donuts which seem better but I haven't been able to locate anything like that in my local hardware store. Can something like that be found in the plumbing section? My only other option is to use some sort of oversized flat nylon washer.
BTW, my laminate trimmer is pretty chintzy so that's as far down as it will go. I tried installing a metal flange but my router bit wouldn't extend beyond it. I may have to ask for a new router for Father's Day!
__________________
(2006) Larrivee OM-03R, (2009) Martin D-16GT, (1998) Fender Am Std Ash Stratocaster, (2013) McKnight McUke, (1989) Kramer Striker ST600, a couple of DIY builds (2013, 2023) |
#27
|
|||
|
|||
I would love to find a better donut too so if you ever do find one post it. I think a lot of people make them from cutting board material. I'm not really tooled up to do that so I never tried it.
|
#28
|
|||
|
|||
Sounds like a perfect candidate for 3D printing. My local library offers walk-up 3D printing, limited to size of the machine and an hour's run time. Maybe I'll model one and try printing it.
|
#29
|
|||
|
|||
Brilliant! Indeed a 3d printer would be perfect for such and application.
|
#30
|
|||
|
|||
Quote:
Frankly though, I'm stumped that such a fitting can't be found easily off the shelf at the local Ace Hardware.
__________________
(2006) Larrivee OM-03R, (2009) Martin D-16GT, (1998) Fender Am Std Ash Stratocaster, (2013) McKnight McUke, (1989) Kramer Striker ST600, a couple of DIY builds (2013, 2023) |