#1
|
|||
|
|||
Slotting a bridge
I have been reading the advantages of having a slotted bridge with unslotted pins. I have been thinking of slotting the bridge on one of my lesser guitars and then turning the pin around so the slot is at the back. If successful, I would try it on my other ones.
Is this advisable and any pointers or tips on how to do it? I thought maybe with needle files? I've done a forum search but not really finding anything.
__________________
Larrivee OM-03 Seagull SWS Maritime Mini Jumbo Alvarez AP70SB Parlor Alvarez AF60SHB Seagull Concert Hall Mahogany Harmony H1215. 1953 An 80 year old Kay (approx) Epiphone ES-339 Epiphone Les Paul 50's Standard 3 home built Strat's |
#2
|
|||
|
|||
|
#3
|
|||
|
|||
The important thing to note is that the goal of slotting is to create an anchor for the ball end of the string so you don't need to to make the key hole slot any deeper then necessary and of course not less. Ramping is different but often times done when slotting. I like to think of it as the slot is deep enough so that the ball barely touches the pin. In theory you should be able to remove the pin when the guitar is fully strung up.
I've heard it mentioned that it's a better idea to rotate your slotted pins one quarter turn so that there is solid pin wood on the front and back and the slots are on the more neutral sides. Or just get unslotted pins I like to use a jig saw blade mounted in a handle followed by before files to clean it up. Some even use a jig saw to slot! |
#4
|
|||
|
|||
Quote:
__________________
Larrivee OM-03 Seagull SWS Maritime Mini Jumbo Alvarez AP70SB Parlor Alvarez AF60SHB Seagull Concert Hall Mahogany Harmony H1215. 1953 An 80 year old Kay (approx) Epiphone ES-339 Epiphone Les Paul 50's Standard 3 home built Strat's |
#5
|
|||
|
|||
I use an unmounted coping saw blade. I rotate it a little in the slot for the larger wound strings. Though the slot is wider than the smaller string gauges, it's certainly narrower than pin slots. I don't think the slot width is very important - as long as the ball end can snug up against the bridge plate it works.
|
#6
|
|||
|
|||
I did this for the E and A pin holes out of necessity on my Alvarez baritone when I was using a 66 gauge E string. Couldn't do it without the bridge pin (which also got damaged from the thick string) precariously popping out.
] (edit: as per other folks here, that's a piece of a jigsaw blade glued to a popsickle stick.) Last edited by jwayne; 02-09-2020 at 03:10 PM. |
#7
|
|||
|
|||
For a few decades, I've used this in an X-Acto knife handle. Clean-up, if needed, with needle files.
https://www.amazon.com/Excel-Blades-...RZ0FHW8Y1707N8 |
#8
|
|||
|
|||
Quote:
__________________
Larrivee OM-03 Seagull SWS Maritime Mini Jumbo Alvarez AP70SB Parlor Alvarez AF60SHB Seagull Concert Hall Mahogany Harmony H1215. 1953 An 80 year old Kay (approx) Epiphone ES-339 Epiphone Les Paul 50's Standard 3 home built Strat's Last edited by Wooly; 02-09-2020 at 05:49 PM. |
#9
|
|||
|
|||
Personally I would rather wear out a slot in an easily replaced pin.
__________________
jf45ir Free DIY Acoustic Guitar IR Generator .wav file, 30 seconds, pickup left, mic right, open position strumming best...send to direct email below I'll send you 100/0, 75/25, 50/50 & 0/100 IR/Bypass IRs IR Demo, read the description too: https://youtu.be/SELEE4yugjE My duo's website and my email... [email protected] Jon Fields |
#10
|
|||
|
|||
Quote:
As opposes to what? The most common damage to bridge plates is strings creeping up the slot in badly fitting, damaged, r poorlly fitted pins. Not to mention that a string end securely fitted Is better for tone. |
#11
|
|||
|
|||
Quote:
Now I don't doubt a long list of boutique builders disagree, but the vast volume manufacturers seem to have found something they agree on.
__________________
jf45ir Free DIY Acoustic Guitar IR Generator .wav file, 30 seconds, pickup left, mic right, open position strumming best...send to direct email below I'll send you 100/0, 75/25, 50/50 & 0/100 IR/Bypass IRs IR Demo, read the description too: https://youtu.be/SELEE4yugjE My duo's website and my email... [email protected] Jon Fields |
#12
|
|||
|
|||
I never really thought about it like that but I suppose one could argue that drilling a hole in the plate woul interrupt the long grain stiffness and so a pinless bridge would be even better.
I think what manufacturers figured out more was a faster and cheaper way of doing something and that it's good enough. And for the most part it is as long as they are well fit. I've yet to see any damage from slotting holes but have seen plenty of damage from missfitted slotted pins. Usually it's when cheaper plastic pins wear out and get bent out of shape and allow the ball end to slide up the hole. |
#13
|
|||
|
|||
And, "some" manufacturers figured out that it was even faster and cheaper to use the same tapered pins but not bother with tapering the holes into which the pins are inserted. They figured out that that is also "good enough".
|
#14
|
|||
|
|||
Quote:
As we assist people to modify their instruments for dubious improvement (most tuning machine replacements come to mind) and chase symptoms of obsession (most minor cosmetic fixes that should only be attempted by an expert), this particular modification seems to not pass the sniff test at production manufacturers. And to some extent we do a disservice promoting potentially destructive modifications.
__________________
jf45ir Free DIY Acoustic Guitar IR Generator .wav file, 30 seconds, pickup left, mic right, open position strumming best...send to direct email below I'll send you 100/0, 75/25, 50/50 & 0/100 IR/Bypass IRs IR Demo, read the description too: https://youtu.be/SELEE4yugjE My duo's website and my email... [email protected] Jon Fields Last edited by jonfields45; 02-10-2020 at 06:38 AM. |
#15
|
|||
|
|||
A thought
I can see how a mass manufacturer would avoid slotting bridge pin holes, the extra work steps could multiply the count of operations expended in installing a bridge, and here's six exposures to destructive error at the end of the build process. Tapering pin holes seems to me to be comparatively risk free, but it still is six more operations compared to none.
I think slotting bridge pin holes is within the skill set of the person who built the instrument in the first place, but it does take time and the task needs respect and care. No task is a throwaway, it seems, in lutherie. Now, I think guitar consumers shouldn't be taking saws and files to their bridges without a well-founded idea that they know what they're doing. I suspect more than one is clueless and is acting on something read in a forum. |