#1
|
|||
|
|||
Rainsong vs. Capo
Suggestions for a good capo for Rainsong steel string guitars? Since the Rainsong fingerboard has almost no radius, and almost all steel string acoustic guitar capos have a curved bar to match a typical neck radius, I tend either to get a buzz on the D and/or G string, since the bar isn't pressing as hard on those middle strings; or, if it's a model with adjustable pressure, and I clamp it down hard enough to work on the middle strings, it' likely to push the two E strings so hard that they go out of tune.
Classical guitar capos don't have the problem, of course, but they're likely to be too lightly built, or, if they use a string, not to have a strong enough one. Also, the bar is build for a wider neck, and hangs off the edge further, and interferes with fingering. But enough griping. Anyone have a solution that I haven't tried? P. |
#2
|
|||
|
|||
G 7th Newport
I've been using the G 7th Newport on my Rainsongs exclusively - N1 and N2 neck.
https://www.g7th.com/newport-capo |
#3
|
|||
|
|||
I've not experienced nylon string, classical capos, designed for flat radius fretboards that aren't designed with enough oomph to handle steel strings. Perhaps they exist, but I'm surprised that you think this issue is common. I use a Shubb on my nylon string and before that Dunlop. Neither looked to be different in construction from their steel-sting capo designs except for the flat radius.
Which nylon string/classical ones have you tried and "failed out?"
__________________
----------------------------------- Creator of The Parlando Project Guitars: 20th Century Seagull S6-12, S6 Folk, Seagull M6; '00 Guild JF30-12, '01 Martin 00-15, '16 Martin 000-17, '07 Parkwood PW510, Epiphone Biscuit resonator, Merlin Dulcimer, and various electric guitars, basses.... |
#4
|
|||
|
|||
I am using a G7 Performance 2. I have one in each RainSong case. Before that I used a Dunlop Trigger capo. I've had no problems with the standard version of these capos and the RainSong 20" fretboard radius.
__________________
jf45ir Free DIY Acoustic Guitar IR Generator .wav file, 30 seconds, pickup left, mic right, open position strumming best...send to direct email below I'll send you 100/0, 75/25, 50/50 & 0/100 IR/Bypass IRs IR Demo, read the description too: https://youtu.be/SELEE4yugjE My duo's website and my email... [email protected] Jon Fields |
#5
|
|||
|
|||
+1 on G7th P2 or P3 for Rainsong necks.
__________________
Dave McPherson Sable, Blackbird Lucky 13, Rainsong OM1000. Various wood, mostly Taylors |
#6
|
|||
|
|||
Never had a problem with a good old Kyser.
Even the 6-string versions work fine. If you like Shubbs, Shubb will custom bend one to 20", but you have to order it directly from them.
__________________
Larrivee OM-03RE; O-01 Martin D-35; Guild F-212; Tacoma Roadking Breedlove American Series C20/SR Rainsong SFTA-FLE; WS3000; CH-PA Taylor GA3-12, Guild F-212 https://markhorning.bandcamp.com/music |
#7
|
|||
|
|||
I primarily use the Dunlop Trigger or the original Shubb. No problems with either on my N1 neck WS-1000. Some capos have trouble handling the 20" Rainsong fret board radius versus the more common 15"-16" radius of other guitar brands.
|
#8
|
|||
|
|||
I also use a Kyser on my NS-necked guitars, without trouble. But I tend to capo right up behind the fret for maximum break angle on the string over the fret.
|
#9
|
|||
|
|||
That MIGHT account for why Keysers sometimes work OK and sometimes don't. I haven't always been careful about the placement thing...
|
#10
|
|||
|
|||
There is a new Ernie Ball capo for flat and radiused retboards. I bought one and it works fine with my Rainsong. One thing though, it is a little heavy.
https://www.sweetwater.com/store/det...E&gclsrc=aw.ds |
#11
|
|||
|
|||
I never have an issue and I never capo anywhere near the fret, those folks are nuts.
__________________
Larrivee OM-03RE; O-01 Martin D-35; Guild F-212; Tacoma Roadking Breedlove American Series C20/SR Rainsong SFTA-FLE; WS3000; CH-PA Taylor GA3-12, Guild F-212 https://markhorning.bandcamp.com/music |
#12
|
|||
|
|||
A little pricy but you could check with Thalia Capos. They have fittings that come with them for various different guitars.
Cheers
__________________
2020 Yamaha LL56 Custom 2021 Boucher SG-51-BMV 2020 RainSong CO-WS1000N2 2019 PRS Silver Sky |
#13
|
|||
|
|||
I have used both the Kyser and Thalia on my CH-PA, no issues noted.
Later Rob |
#14
|
|||
|
|||
I’m sure you are fully aware by now, but in case you are not I thought I would mention this...
If you buy a thalia capo the fittings that come with them by default do not provide coverage for a Rainsong. You need to pay another 7 bucks to get a special fit kit designed specifically for Rainsong. I had to look into this myself because I just purchased a Rainsong. Cheers
__________________
2020 Yamaha LL56 Custom 2021 Boucher SG-51-BMV 2020 RainSong CO-WS1000N2 2019 PRS Silver Sky |
#15
|
|||
|
|||
__________________
YUP.... Emerald: X-20, Center hole X-10 (Maple) and X-7 (redwood), Spalted Chen Chen X 10 level 3, CA: Early OX and Cargo McPherson: Early Kevin Michael Proto Some wood things by Epi, Harmony, Takamine, Good Time, PRS, Slick, Gypsy Music, keyboards, wind controllers.. etc |