The Acoustic Guitar Forum

The Acoustic Guitar Forum (https://www.acousticguitarforum.com/forums/index.php)
-   Custom Shop (https://www.acousticguitarforum.com/forums/forumdisplay.php?f=38)
-   -   Chasson Jumbo and Concert for TAMCO (https://www.acousticguitarforum.com/forums/showthread.php?t=247896)

Kent Chasson 04-13-2012 04:56 PM

Chasson Jumbo and Concert for TAMCO
 
I'm working on 2 more for The Acoustic Music Company.

The first is a full 17" wide Sitka/Maple jumbo. I don't get to build too many of these so I was happy that Trevor wanted one. I sent him photos of 2 of the sets of Maple I have and he chose my favorite of the two. It is not the traditional straight even flame but a bit more organic. There is amazing depth to the figure which of course will show up even more under finish.

He's also getting the first of my re-designed Concert Models. I offered a Concert many years ago but after several design tweaks, it grew to Auditorium size. The new one is back to 15" at the lower bout and pretty excited to get one strung up. I love that size.

I was finishing a Parlor at the same time I was gluing linings on the Jumbo. Gives you an idea of the size range!

http://www.chassonguitars.com/images/77/parlor.jpg

We decided on a high contrast theme with all ebony trim and Black/White purfling lines.

http://www.chassonguitars.com/images/77/77_front.jpg

The back was probably just barely wide enough but I decided to go ahead and add the wedged back stripe. I've always liked that look and the extra width gave me some leeway.

http://www.chassonguitars.com/images/77/77_back1.jpg

I then decided to reverse the typical direction of the end graft taper to mirror the back stripe.

http://www.chassonguitars.com/images/77/77_end.jpg

http://www.chassonguitars.com/images/77/77_detail.jpg

I'll get some photos of the Concert up soon. Thanks for looking.

KolayaGuitars 04-13-2012 04:58 PM

This is very nice! Love the back strip continuation through the end graft. Very clean work!

Simon Fay 04-13-2012 05:00 PM

Very nice job on the tail inlay - a subtle difference but one that I think makes a big overall impact. Beautiful work!!!

Larry Pattis 04-13-2012 06:17 PM

Excellent...

Joel Stehr 04-13-2012 06:27 PM

Sweet! Nice details and stunning maple!

Joel

ChuckS 04-13-2012 07:03 PM

That looks extremely nice Kent.

Steve Kinnaird 04-13-2012 07:13 PM

Yeah Kent, sweet tail wedge detail. Very clever.

Steve

Trevor M 04-14-2012 02:28 AM

Thanks Kent, Love the parlour/jumbo shot it would be great to see a similar shot of finished guitars sometime.

The end graft and back stripe is inspirational, one of those simple ideas that makes you think 'why has no one thought of that before.'

Its a while since I've had a 17" in stock, years ago the big jumbo was my favourite size, mow its OO, not sure what that says.. bit I am really looking forward to this one, you never know I might change back, or have two favourite sizes..

racman 04-14-2012 04:00 AM

Beautiful looking guitar already Kent!

jeastman 04-14-2012 04:23 AM

Beautiful work. That's going to look amazing under finish.

Mark Hatcher 04-14-2012 06:46 AM

Kent,

That center and end graft combo is striking! Really great design.

Mark

Kent Chasson 04-14-2012 10:24 AM

Thanks for the kind words everybody.

Tom Doerr 04-14-2012 10:40 AM

Great work Kent! I actually saw your wenge guitar today as I was dropping off my guitars to Tony's. There even better in person :)

Kent Chasson 04-24-2012 10:46 PM

An update with lots of photos.

The Jumbo is on the way to finish. I'll get more photos of that when it's shiny.

For now, the new Concert Model. It has an Engelmann Spruce top, Wenge Back/Sides with Leopardwood trim.

This shot is a bit distorted but it gives you an idea of the new shape.

http://www.chassonguitars.com/images/trevor/back.jpg

http://www.chassonguitars.com/images.../rims_back.jpg

I've really changed my methods of work over the years. I've increased the amount of hand work I do while refining the machine work and I'm really happy with the balance. I used to use the jointer to prep my plates for gluing but I've gone back to a hand plane. It's just as fast and it's quiet and enjoyable.


http://www.chassonguitars.com/images...ting_board.jpg

And I've gone from vacuum clamping back to the old fashioned go-bar deck. Mostly it's just quieter but vacuum doesn't work very well with the hot hide glue I use for top bracing.

http://www.chassonguitars.com/images/trevor/go_bar.jpg

On the other end of the spectrum is my pin router (the one on the left). I think this is the coolest tool in the shop but I may be alone in that.;) It's used for pattern cutting. There is a pin in the table centered on the bit. A pattern rides on the pin and the bit cuts to the shape of the pattern. But the cool thing about it is that the pin size is variable so I can fine tune the cut without messing with the pattern.

http://www.chassonguitars.com/images/trevor/routers.jpg

http://www.chassonguitars.com/images...pin_router.jpg

Here it is with my rosette pattern. The two patterns are for two different sizes. The pin rides in the channel and the router bit above cuts the recess for the rosette.

http://www.chassonguitars.com/images...tte_female.jpg

http://www.chassonguitars.com/images...ostte_slot.jpg

Kent Chasson 04-24-2012 10:47 PM

This is the male pattern to cut the inlay. Here's where the adjustable pin comes in. I don't want the inlay to be the same size as the slot. I want it smaller by the width of the purfling plus a little extra slop because everything expands when you add glue. So with the same pattern, I can use different thicknesses of purfling by changing the size of the pin. I have a set of pins graduated in .001" increments so In can really fine tune it.

http://www.chassonguitars.com/images...sette_male.jpg

http://www.chassonguitars.com/images...sette_body.jpg

Here are segments of the rosette before and after purfling.

http://www.chassonguitars.com/images...e_sections.jpg

http://www.chassonguitars.com/images...te_section.jpg

The router leaves rounded corners so before inlaying, I have to go back and square the corners with a small chisel. That and the mitered purfling is why I finally broke down and bought these loupes! They drive you batty after awhile (no wonder dentists are sadistic!) but they momentarily restore my slowly fading eyesight.

http://www.chassonguitars.com/images/trevor/loupes.jpg

Got the top on tonight and will do final voicing tomorrow (more hand work).

Thanks for indulging me.


All times are GMT -6. The time now is 04:24 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright ©2000 - 2022, The Acoustic Guitar Forum

vB Ad Management by =RedTyger=