#1
|
|||
|
|||
Scratches
So I took my Martin OM-21 to a dealer to get a set-up done. They did a good job on the set-up, but once I got it home I noticed a small scrape on the top under the low E string between the sound hole and the bridge. When I took the guitar in it was mint. They didn't mention that they scratched my guitar when I picked it up... so I want nothing to do with them any more. But what can I do about reducing a small scrape in the finish? It is less than a half inch scrape to the finish, no wood exposed, and when I run a fingernail across the scratch I can barely feel the indentations. So far I've been ignoring it, but the more I think about it the more it bothers me. Would "guitar polish" help to reduce the blemish? Any suggestions on product to use? I don't want to mess up the finish any more than it already is, but I sure would like to make the mark less obvious.
|
#2
|
|||
|
|||
Photos needed to advise properly.
For info on the legalities side, morally we try to fix any damage that occurs when an instrument is in our hands, we are human and things sometimes happen. Legally when you take your instrument in for repairs, the law does not cover you, your instrument when taken to a repairer is deemed as damaged to start with, the repairer/builder, provided they exercise all cautions, they are not legally accountable for any minor damage that may occur in fixing the job they were contracted to do. It is a different scenario however if they pick your guitar up and smash it against a bench with malicious intent. Steve
__________________
Cole Clark Fat Lady Gretsch Electromatic Martin CEO7 Maton Messiah Taylor 814CE |
#3
|
|||
|
|||
I probably should have left the back story out of my post. All I really wanted to ask is if it is safe to try to buff out a scuff in a nitro finish, and if so what products are recommended? Is the risk of doing more harm than good as a complete klutz sufficient that I should just ignore it and practice playing more?
Last edited by Vinegar; 03-12-2018 at 11:18 PM. |
#4
|
|||
|
|||
The scratch is pretty deep, if you were to sand and buff then you are lowering the whole area around it to that height
Repair process for at home With 1000 grit sandpaper (wet and detergent) lightly scuff / clean the area of concern, approx the 1 inch in size Buy a can of nitro spray lacquer, spray the lacquer into a cup Use a toothpick and dip into the sprayed lacquer and deposit build the scratched surface up Allow 1`week to dry Lightly wet sand the surface again with 1000 grit paper on a rubber backed block Hand buff or machine buff area for gloss Steve
__________________
Cole Clark Fat Lady Gretsch Electromatic Martin CEO7 Maton Messiah Taylor 814CE |
#5
|
|||
|
|||
Thank you for the advice, but that sounds like a task for someone with some skill and experience. I think I'll try to forget it is there.
|
#6
|
|||
|
|||
Best thing you can do. You're better off the way it is than turning the little scratch into a crack
|
#7
|
|||
|
|||
I agree. You are best to ignore it and leave it alone as attempted repair without lots of experience can lead to additional issues. An experienced professional should only be the one working on finish issues of a valuable guitar in my opinion if any work should be done at all. It seems the new style is the aged look anyway.
|
#8
|
|||
|
|||
Quote:
|
#9
|
||||
|
||||
Quote:
Another way is to get a tiny bottle of Testor's clear gloss model building lacquer.
__________________
Fazool "The wand chooses the wizard, Mr. Potter" Taylor GC7, GA3-12, SB2-C, SB2-Cp...... Ibanez AVC-11MHx , AC-240 |
#10
|
|||
|
|||
Quote:
If the guitar is an acrylic finish, Uv finish, Poly urethane etc, then yes super glue is good. Steve
__________________
Cole Clark Fat Lady Gretsch Electromatic Martin CEO7 Maton Messiah Taylor 814CE |
#11
|
|||
|
|||
At least forget about it until you scratch it yourself somewhere else. Then it is broken in.
|