The Acoustic Guitar Forum

Go Back   The Acoustic Guitar Forum > General Acoustic Guitar and Amplification Discussion > Acoustic Amplification

Reply
 
Thread Tools
  #1  
Old 04-19-2017, 05:58 AM
jonfields45 jonfields45 is offline
Registered User
 
Join Date: Jun 2011
Location: Allentown, PA
Posts: 4,603
Default Wiring instructions Mi-Si VTC to new Trio based on Air 2.0 PCB

Mi-Si has switched to a common circuit board, different parts are populated, for their new Air (only) pickup and the older Trio. I bought a VTC (volume/tone control) but the instructions are for the older Trio circuit board and I have the new Trio. Calls and emails to Mi-Si have not been returned. Does anyone have the wiring instructions?
__________________
jf45ir Free DIY Acoustic Guitar IR Generator
.wav file, 30 seconds, pickup left, mic right, open position strumming best...send to direct email below
I'll send you 100/0, 75/25, 50/50 & 0/100 IR/Bypass IRs
IR Demo, read the description too: https://youtu.be/SELEE4yugjE
My duo's website and my email... [email protected]

Jon Fields
Reply With Quote
  #2  
Old 04-19-2017, 08:27 AM
jonfields45 jonfields45 is offline
Registered User
 
Join Date: Jun 2011
Location: Allentown, PA
Posts: 4,603
Default

Ted at Blue Star Music was able to get me the instructions. I've pasted the main picture below. It does require the removal of a surface mount resistor (edit: before I removed it I measured it and it is just a jumper) which is not the easiest first soldering project. I've got a digitally controlled solder vacuum and expect no problems. I give Blue Star Music extremely high marks for customer service!

__________________
jf45ir Free DIY Acoustic Guitar IR Generator
.wav file, 30 seconds, pickup left, mic right, open position strumming best...send to direct email below
I'll send you 100/0, 75/25, 50/50 & 0/100 IR/Bypass IRs
IR Demo, read the description too: https://youtu.be/SELEE4yugjE
My duo's website and my email... [email protected]

Jon Fields

Last edited by jonfields45; 04-19-2017 at 07:19 PM.
Reply With Quote
  #3  
Old 04-19-2017, 03:44 PM
jonfields45 jonfields45 is offline
Registered User
 
Join Date: Jun 2011
Location: Allentown, PA
Posts: 4,603
Default

All done. Works fine. As you can see I'm a big 3M Velcro-like product user. It is holding the wires down and the VTC at the soundhole.

http://s646.photobucket.com/user/jon...20Installation
__________________
jf45ir Free DIY Acoustic Guitar IR Generator
.wav file, 30 seconds, pickup left, mic right, open position strumming best...send to direct email below
I'll send you 100/0, 75/25, 50/50 & 0/100 IR/Bypass IRs
IR Demo, read the description too: https://youtu.be/SELEE4yugjE
My duo's website and my email... [email protected]

Jon Fields
Reply With Quote
  #4  
Old 04-20-2017, 05:34 AM
jonfields45 jonfields45 is offline
Registered User
 
Join Date: Jun 2011
Location: Allentown, PA
Posts: 4,603
Default

I did hear from Mi-Si this morning with the same instructions. According to Mi-Si they have gone back to the old PCB for the Trio and only briefly shipped Trio's with a common circuit board with the Air only product.
__________________
jf45ir Free DIY Acoustic Guitar IR Generator
.wav file, 30 seconds, pickup left, mic right, open position strumming best...send to direct email below
I'll send you 100/0, 75/25, 50/50 & 0/100 IR/Bypass IRs
IR Demo, read the description too: https://youtu.be/SELEE4yugjE
My duo's website and my email... [email protected]

Jon Fields
Reply With Quote
Reply

  The Acoustic Guitar Forum > General Acoustic Guitar and Amplification Discussion > Acoustic Amplification






All times are GMT -6. The time now is 06:52 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright ©2000 - 2022, The Acoustic Guitar Forum
vB Ad Management by =RedTyger=