#1
|
|||
|
|||
Build of yore - Electric Thin Line Archtop Nylon String
So I stumble upon a long-lost USB jump drive that just happened to have some archived photos of a few builds. Thought it would be fun to share this. This build was originally done around the fall of 2010, only a little more than a month after my mother's passing. The guitar had moved along to it's current owner since.
This guitar was actually a "challenge" build in the ol' MIMF; maybe some of the folks here may remember. Anyways, I remember Gibson came out with a custom nylon-string LP where the bridge was actually carved into the top. Always liked the clean look of that, but thought it would be cool to make an LP-type guitar that was nylon string, but had a stop-tail as well. This was a conundrum, as I wanted a fully carved top plate. I start off with this template, which is a copy of a OO template I made for another challenge guitar (which had since imploded after a fall): [IMG]007-Template After by Louie Atienza, on Flickr[/IMG] The top would be made of this cedar, which believe it or not, was a "save" from a decking job I did about 5 years prior. Had some cool discoloration, but was decently quartered: [IMG]008-Resaw Top by Louie Atienza, on Flickr[/IMG] Being it was a 6X6 post it needed to be glued up out of 4 pieces: [IMG]011-Bookmatch Sort Of by Louie Atienza, on Flickr[/IMG] I also fell into a lot of this crazy Philippine mahogany, and made a few LP bodies from it later. I actually had some resawn a year ago by Chris Ensor, but only succeeded in bending one pair of sides. Alas there is no more, save for some drop-offs. [IMG]013-Back Blank by Louie Atienza, on Flickr[/IMG] Routing the top shape out using the template as a guide: [IMG]015-Top Route by Louie Atienza, on Flickr[/IMG] Last edited by LouieAtienza; 11-18-2017 at 02:46 PM. |
#2
|
|||
|
|||
So although I had my CNC up and running, my self-imposed challenged was to devise a jig that would do what I call a "proportional" arch on the top, without having to use an already carved template and pantograph. This was the jig I devised, and will carve an arch on a body of almost any shape, without prior templating.
[IMG]016-Top Rough Pass 1 by Louie Atienza, on Flickr[/IMG] Some folks at the MIMF were a bit concerned about my prior "hazardous" carving techniques. This was far more safer, and the roughing consumed about 15 minutes or so of relatively easy work. [IMG]017-Top Rough Pass 2 by Louie Atienza, on Flickr[/IMG] [IMG]018-Top Cleaned 1 by Louie Atienza, on Flickr[/IMG] The back was glued up and cut to shape: [IMG]021-Back Cutout by Louie Atienza, on Flickr[/IMG] And the template for the "hollowing out was made: [IMG]023-Chamber Template 2 by Louie Atienza, on Flickr[/IMG] Leading to the not-too-fun task of hogging out: [IMG]025-Chamber Route 1 by Louie Atienza, on Flickr[/IMG] [IMG]026-Chamber Route Done by Louie Atienza, on Flickr[/IMG] So far: [IMG]027-Mockup 1 by Louie Atienza, on Flickr[/IMG] |
#3
|
|||
|
|||
Neck billet glued up from more Philippine mahogany, padauk, and maple:
[IMG]032-Neck Mockup by Louie Atienza, on Flickr[/IMG] A chunk of phenolic (arborite) that I use mainly for electric guitar fretboards: [IMG]034-Fretboard Blank by Louie Atienza, on Flickr[/IMG] [IMG]035-Fretboark Blank Cut by Louie Atienza, on Flickr[/IMG] [IMG]036-Fretboard Planing by Louie Atienza, on Flickr[/IMG] [IMG]038-Fretboard Slots by Louie Atienza, on Flickr[/IMG] Then brought onto my fretboard radiusing jig: [IMG]039-Fretboard Radius 1 by Louie Atienza, on Flickr[/IMG] [IMG]040-Fretboard Radius 2 by Louie Atienza, on Flickr[/IMG] [IMG]042-Fretboard Radius 4 by Louie Atienza, on Flickr[/IMG] |
#4
|
|||
|
|||
Fretboard glued with epoxy to neck billet, which has ears added to the headstock, and getting flushed on belt sander:
[IMG]055-Neck Sand Side by Louie Atienza, on Flickr[/IMG] The laborious task of removing the mill marks from the fretboard: [IMG]057-Fretboard Sand 2 by Louie Atienza, on Flickr[/IMG] Phenolic looks really nice all polished up: [IMG]058-Fretboard Sand 3 by Louie Atienza, on Flickr[/IMG] [IMG]063-Fretting 5 by Louie Atienza, on Flickr[/IMG] When you don't have a bandsaw you have to resort to caveman tactics: [IMG]070-Cutting Taper by Louie Atienza, on Flickr[/IMG] Rough-shaping the neck using aforementioned jigsaw, rasps, and sandpaper: [IMG]075-Neck Shaping Done by Louie Atienza, on Flickr[/IMG] The arched top is hollowed out using a Forstner bit on the drill press. A roll of tape underneath serves as a guide: [IMG]077-Top Rough Done by Louie Atienza, on Flickr[/IMG] Scraped, sanded, and almost ready: [IMG]079-Top Done by Louie Atienza, on Flickr[/IMG] |
#5
|
|||
|
|||
Spalted maple gifted to me by fellow MIMFer:
[IMG]081-Headstock Veneer 1 by Louie Atienza, on Flickr[/IMG] [IMG]082-Headstock Veneer 2 by Louie Atienza, on Flickr[/IMG] The back "braces" are shaped, along with the two "bosses" that will be used for the pins for the "floating" stop-tail: [IMG]084-Bracing Carve 1 by Louie Atienza, on Flickr[/IMG] And the corresponding holes on the top: [IMG]087a-Top Drill 2 by Louie Atienza, on Flickr[/IMG] Headstock rough shaped: [IMG]095-Headstock Shape by Louie Atienza, on Flickr[/IMG] [IMG]103-Headstock Bevel Done by Louie Atienza, on Flickr[/IMG] Binding: [IMG]101-Binding Glue Up by Louie Atienza, on Flickr[/IMG] [IMG]106-Binding Top Bout Done by Louie Atienza, on Flickr[/IMG] |
#6
|
|||
|
|||
The tenon is shaped onto the neck heel:
[IMG]112-Neck Tenon Cut by Louie Atienza, on Flickr[/IMG] Was afraid the neck pocket wall at the cutaway would be too frail so I reinforced it with padauk. The neck wood under the fretboard was also shaped to the top. Having a continuous neck piece all the way through ensures me of no hump: [IMG]113-Body Tenon Cut by Louie Atienza, on Flickr[/IMG] [IMG]114-Neck Joint Detail 1 by Louie Atienza, on Flickr[/IMG] Finishing the headstock: [IMG]116-Tuner Holes 1 by Louie Atienza, on Flickr[/IMG] [IMG]117-Tuner Holes 2 by Louie Atienza, on Flickr[/IMG] [IMG]118-Tuner Holes 4 by Louie Atienza, on Flickr[/IMG] |
#7
|
|||
|
|||
Bridge and stop tail carved from padauk:
[IMG]121-Bridge Carved by Louie Atienza, on Flickr[/IMG] [IMG]122-Tailpiece Drilling by Louie Atienza, on Flickr[/IMG] [IMG]123-Tailpiece and Bridge Finished by Louie Atienza, on Flickr[/IMG] The guitar's first coat of finish: [IMG]125-Front Preview by Louie Atienza, on Flickr[/IMG] [IMG]126-Back Preview by Louie Atienza, on Flickr[/IMG] More spalted maple which would become the back plate: [IMG]127-Back Plate by Louie Atienza, on Flickr[/IMG] And the finished guitar: [IMG]131-Front-1 by Louie Atienza, on Flickr[/IMG] [IMG]132-Headstock-1 by Louie Atienza, on Flickr[/IMG] [IMG]133-Top-1 by Louie Atienza, on Flickr[/IMG] Detail of how the stop tail works. Originally I used flat head screws, but they ended up bending from the string pull. I eventually turned to posts from drill rod. [IMG]134-Bridge Detail by Louie Atienza, on Flickr[/IMG] |
#8
|
|||
|
|||
That's really neat Louie. What does it sound like?
|
#9
|
|||
|
|||
Thanks... I do have a soundclip, somewhere. If I find it I'll post it. Surprisingly good for a guitar without a sound hole. Because this was part of a $100 challenge, I put what was likely the cheapest feather pickup ever (about 13 on eBay.) The tuners were the costliest part and they were Ping's for about $40 at GC. The pickups kind of give a "uke" effect; unfortunately I didn't record the "acoustic" sound. Could have been my rough fingers and carpal tunnel... Very happy with the trebles, didn't want booming bass because it was meant to be amplified.
|
#10
|
|||
|
|||
Of course as I go to look for something else I find the track. Please excuse the "rough" playing...
|