#1
|
|||
|
|||
Repair advice please - pushed through jack socket
So, this happened where the jack socket used to come out on my Ibanez:
I've had similar problems repaired on another instrument in the past where a tech has put a plate over the damage. A friend has passed me a plastic 'football' Telecaster jack socket plate that should hopefully do the job. Is this something I should attempt myself? I'm reasonably adept at building CBGs & stomp boxes, but I've always been hesitant to attempt jobs on my 'proper' instruments. If I do attempt it, should I be taking steps to reinforce the wood around the damage before fitting the jack socket plate? The wood seems solid enough, but there are one or two fine cracks visible around where the hole is.
__________________
"I used to think I was an artist. Come to find out I'm a beer salesman" - James McMurtry Hear some footstomping acoustic blues at pistolpetewearn.co.uk! Last edited by PistolPete; 03-07-2018 at 10:48 AM. Reason: The pictures were *massive* |
#2
|
|||
|
|||
It would be best to glue(HHG or Titebond) a reinforcing patch on the inside, but access is difficult. If you think you can get to it, a cross grain patch about 2" long and less than 1/8" thick should do it. Thicker may be difficult to fit to the curve.
__________________
Rodger Knox, PE 1917 Martin 0-28 1956 Gibson J-50 et al |
#3
|
|||
|
|||
LOL I just fixed two of them not too long ago, by getting a jack plate. I didn't use the plastic oval ones, but the metal Gibson style plates. I used a piece of thin metal strip bent at the end, and double sided tape on it, to place reinforcement pieces on each corner where the new screws will go, and allow a thicker grab for the screws. It's IMPORTANT to drill a pilot hole before inserting new screws.
I think inserting a full size patch would be excessive and expensive, relative to the value of the instrument. But next time, REMOVE the guitar cable before placing the guitar on a stand or leaning it against an amp or whatever! |
#4
|
|||
|
|||
The tricky part of this repair is that the body is a laminate.
Very hard and time consuming to make a laminated hole look good again. Accept that and the rest is easy, patch it, smooth it, play it Steve
__________________
Cole Clark Fat Lady Gretsch Electromatic Martin CEO7 Maton Messiah Taylor 814CE |
#5
|
|||
|
|||
Thank you all so much for your advice.
I got myself a square plate, after realising that the screw from the oval one was going to sit directly on the crack I was worried about. So I had to tidy up & enlarge the hole a little to make it fit, then, in light of what was said here, I glued a shim either side of the hole on the inside to reinforce the screws a little bit, drilled pilot holes and fitted the new plate. I admit, it's not world-class-luthier stuff, but seems solid & should be good enough for a £350 Chinese jazz guitar I think. Anyhow, here's my hole now:
__________________
"I used to think I was an artist. Come to find out I'm a beer salesman" - James McMurtry Hear some footstomping acoustic blues at pistolpetewearn.co.uk! |
#6
|
|||
|
|||
Nice repair job. You’ll be the only one that knows the guitar didn’t come with the escutcheon.
__________________
Taylor V-Class 814ce, 717e BE WHB, 520ce, 454ce, 420 Cedar\Maple, T5z Classic Martin D18E Retro Cordoba C10 Crossover Emerald X20 Rainsong H-OM1000N2 Voyage-Air VAD-04 Custom Les Paul Hot Rod Deville 410, Fishman Loudbox Performer |
#7
|
|||
|
|||
Quote:
I had to look up 'escutcheon' - good word
__________________
"I used to think I was an artist. Come to find out I'm a beer salesman" - James McMurtry Hear some footstomping acoustic blues at pistolpetewearn.co.uk! |