The Acoustic Guitar Forum

Go Back   The Acoustic Guitar Forum > General Acoustic Guitar and Amplification Discussion > Build and Repair

Reply
 
Thread Tools
  #1  
Old 04-04-2017, 08:50 AM
Bonneybear Bonneybear is offline
Registered User
 
Join Date: Jun 2010
Posts: 23
Default Bridge plate for 00-42 steel string

Hi everyone, it's a bit of a hybrid build, my question is wood choice and cut. I'm thinking either Osage orange, maple or rosewood. The bigger question is cut. I've hear rift sawn, I don't really know what that means, I've seen different and contradicting descriptions of rift sawn wood. Can someone please explain? Also which direction should the grain run in reference to the spruce top grain. Thanks in advance. Mike
Reply With Quote
  #2  
Old 04-04-2017, 09:02 AM
Bonneybear Bonneybear is offline
Registered User
 
Join Date: Jun 2010
Posts: 23
Default

is there an easy way to post pics?
Reply With Quote
  #3  
Old 04-04-2017, 03:07 PM
Bonneybear Bonneybear is offline
Registered User
 
Join Date: Jun 2010
Posts: 23
Default


Last edited by Bonneybear; 04-05-2017 at 08:59 PM.
Reply With Quote
  #4  
Old 04-04-2017, 11:25 PM
John Arnold John Arnold is offline
Registered User
 
Join Date: Jan 2009
Posts: 4,082
Default

To me, rift cut means grain that is between vertical and flat. Usually between 30 and 60 degrees to the face. Around 45 degrees is the least likely to split, but my 33 years of experience as a full time guitar repairman tells me that split bridgeplates are almost always the result of a severely lifted bridge. In general, bridges lift because the guitar got overheated. I run the grain in the plate straight across...at right angles to the grain in the guitar top.
Reply With Quote
  #5  
Old 04-05-2017, 08:05 PM
Bonneybear Bonneybear is offline
Registered User
 
Join Date: Jun 2010
Posts: 23
Default


Last edited by Bonneybear; 04-05-2017 at 09:10 PM. Reason: Bad pic
Reply With Quote
  #6  
Old 04-05-2017, 08:12 PM
Bonneybear Bonneybear is offline
Registered User
 
Join Date: Jun 2010
Posts: 23
Default


Last edited by Bonneybear; 04-05-2017 at 09:28 PM. Reason: posting photo issues
Reply With Quote
  #7  
Old 04-05-2017, 08:16 PM
Bonneybear Bonneybear is offline
Registered User
 
Join Date: Jun 2010
Posts: 23
Default


Last edited by Bonneybear; 04-05-2017 at 09:30 PM. Reason: Pic replace
Reply With Quote
  #8  
Old 04-05-2017, 08:38 PM
Bonneybear Bonneybear is offline
Registered User
 
Join Date: Jun 2010
Posts: 23
Default


Last edited by Bonneybear; 04-05-2017 at 09:31 PM. Reason: cannot see the image i just posted.
Reply With Quote
  #9  
Old 04-05-2017, 08:44 PM
Howard Klepper Howard Klepper is offline
Registered User
 
Join Date: May 2008
Location: Earthly Paradise of Northern California
Posts: 6,627
Default

If those are photos of how you glued the braces in--with a single go bar for the X and a single go bar for the two "tone bar" diagonals--you need to take those braces off (which will be easy) and get some instruction about clamping. IMO many builders underclamp, but this is extreme.
__________________
"Still a man hears what he wants to hear, and disregards the rest."
--Paul Simon
Reply With Quote
  #10  
Old 04-05-2017, 09:35 PM
Bonneybear Bonneybear is offline
Registered User
 
Join Date: Jun 2010
Posts: 23
Default

No those 2 go bars are just holding the top in the dish till I figure out my next move. If anything, I always overclamp with many bars. Thanks though. I think I finally figured out how to post pictures. Technology is good,,, until it isn't .
Reply With Quote
Reply

  The Acoustic Guitar Forum > General Acoustic Guitar and Amplification Discussion > Build and Repair

Thread Tools





All times are GMT -6. The time now is 12:23 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright ©2000 - 2022, The Acoustic Guitar Forum
vB Ad Management by =RedTyger=