#1
|
|||
|
|||
Removing finish on vintage Gibson L30
So I bought a 1936 or possibly 1937 Gibson L30. Lady's late husband was a luthier and was going to repair the guitar before passing away. The top and sides are original and and have been stripped of about 85% of the original finish. Sides have a reminat of pink staining. The top has it around the edges. I removed the back because it was cheap plywood. Saved the braces as best I could. Going to put on a new back eventually.
So what's the best was to remove the rest of the left over finish? Acetone? Sanding?
__________________
2014 Martin D17m (Agnus) 2013 John Mayer Fender Strat (Georgia) 1937 Gibson L-30 2019 Fender Paramount pm-te all hog 1997 Epiphone Les Paul Custom |
#2
|
|||
|
|||
I'd ask the mods to repost this in the Build & Repair Forum - you're more likely to get the right advice over there...
__________________
"Mistaking silence for weakness and contempt for fear is the final, fatal error of a fool" - Sicilian proverb (paraphrased) |
#3
|
|||
|
|||
Given that it's not going to be a L30 after you are done historic correctness becomes less important that ending up with a good instrument, so what I would do is use chemical means to remove as much as possible, then sand carefully trying to remove as little wood as possible. I would carve a new back, probably of mahogany as it is actually a great tone wood for the back of an archtop, and I would revoice the top to match the back (different tap tones being key). I would close the box and refinish with modern techniques, probably fairly dark to even out blotches in the top and how it takes up new stain, maybe even an opaque finish. If you take care in how you tune the top and new back you stand a great chance of having a great sounding acoustic instrument. As long as you are up-front and proud about the modifications, no harm done.
Brian
__________________
Brian Evans Around 15 archtops, electrics, resonators, a lap steel, a uke, a mandolin, some I made, some I bought, some kinda showed up and wouldn't leave. Tatamagouche Nova Scotia. |
#4
|
|||
|
|||
Thank you for the response. I bought a new book matched maple back last night, mainly b/c it's what originally came with the guitar. The guy who put the plywood back on ages ago did a really good job, with really sub par wood :-(. I'll continue working on cleaning up the top and sides. I got a quote to fix the top cracks and kurfling, new braces, and install the back and new binding....grand total estimated at $2000. Yikes! So this will have to just be a diy project.
__________________
2014 Martin D17m (Agnus) 2013 John Mayer Fender Strat (Georgia) 1937 Gibson L-30 2019 Fender Paramount pm-te all hog 1997 Epiphone Les Paul Custom |
#5
|
|||
|
|||
Good luck, I assume you are going with a flat back, which is indeed what they came with. I was actually pretty sure that they came with laminated mahogany backs and sides, not solid, but I've never seen a picture of one with maple. If the rims and linings are in good shape bracing and installing a flat back should be pretty easy, the hard part is finishing.
Brian
__________________
Brian Evans Around 15 archtops, electrics, resonators, a lap steel, a uke, a mandolin, some I made, some I bought, some kinda showed up and wouldn't leave. Tatamagouche Nova Scotia. |
#6
|
|||
|
|||
I've got (what I believe to be) an L-37, which is sunburst, and has back binding. I LOVE that guitar. It sounds wonderful! I thought the L-30 was the black archtop without back binding. Pretty much the same guitar otherwise. All the examples I've seen have been hard maple with flat backs. A black one (L-30?) just left my shop after having its back removed, several braces reglued, and tons of back cracks glued and cleated. I think it might have been easier just to replace the back, but this way, it's all original.
Most of these have flat-sawn unfigured hard maple backs and sides. I think because they're flatsawn, the backs are more prone to distorting and cracking. Therefore, many examples of these guitars have back cracks and loose braces. I think I would use a scraper for most of the finish removal to preserve as much of the sides' thickness as possible.
__________________
https://www.reverbnation.com/bootheelers |
#7
|
|||
|
|||
Quote:
__________________
2014 Martin D17m (Agnus) 2013 John Mayer Fender Strat (Georgia) 1937 Gibson L-30 2019 Fender Paramount pm-te all hog 1997 Epiphone Les Paul Custom |