Hatcher Piña 0 model Green Mountain Series
Here is my latest start on a Green Mountain Series Piña 0 model. It will be tri-color bear claw Sitka floatwood on Bavarian Plum. Doesn't that sound delicious?
https://live.staticflickr.com/65535/...0a5dab52_b.jpg The Plum wood species is Prunus Domestica. I say Bavarian because that is where I got this wood from. https://live.staticflickr.com/65535/...c74b93b3_b.jpg Plum wood is a nice middleweight wood coming in at about 50lbs per cubic foot. https://live.staticflickr.com/65535/...501c2a41_c.jpg The colors are fantastic! https://live.staticflickr.com/65535/...e6921e94_b.jpg I'm matching the Bavarian Plum with this multi colored bear claw Sitka. https://live.staticflickr.com/65535/...12f6a080_c.jpg This Sitka is salvaged from a disassembled floating Alaskan lumber camp. https://live.staticflickr.com/65535/...0d88c70d_c.jpg They float these camps on these giant Sitka logs which they can then move around with tug boats. https://live.staticflickr.com/65535/...d001ca0f_c.jpg The blue color in the Sitka comes from these rusty cleats that are used when lashing the float logs together. These rafts last about thirty to forty years before the cables start to rust out. https://live.staticflickr.com/65535/...8263b6f8_b.jpg I think these two are a great match both for tone and looks. https://live.staticflickr.com/7909/4...559f6246_b.jpg |
I think I am quite familiar with a certain guitar with similar color pattern and it is might purdy.
|
I love the wood choices in this one, Mark. The Bavarian plum is going to be absolutely amazing under finish!
|
Quote:
Quote:
Mark |
Good looking start!
Are you using that black marble looking material for binding/rosettes, or is that just your table??!! Either way, I'm down for it!!:D:D |
Your work always makes me smile...so inspirational!!!:):)
|
Quote:
Quote:
Mark |
Sweet Woods!!!
I am in for this thread!!
Following for sure That Plum is mighty tasty Paul |
Quote:
Mark |
Getting Started
Well let's get started! I usually start with joining the plates
https://live.staticflickr.com/65535/...74092e6f_c.jpg Then it's thicknessing and prepping the surfaces https://live.staticflickr.com/65535/...34cd74dc_c.jpg My preferred method of surfacing wood for gluing is using a smoothing plane. I was having difficulty planning because I kept getting small surface checks. So I resorted to using my cabinet scraper https://live.staticflickr.com/65535/...968a9e25_c.jpg Planning is the best surface for gluing. Scrapping is a close second. With all those braces being glued to the inner surfaces of the top and back sanding should be avoided https://live.staticflickr.com/65535/...a9a8c112_c.jpg This came up clean and saw dust free https://live.staticflickr.com/65535/...bfda1d6a_c.jpg No problem going back to the smoothing place for top thicknessing and surface prepping https://live.staticflickr.com/65535/...68e2cef1_b.jpg I love the symmetry I'm getting with the bear claw figure https://live.staticflickr.com/65535/...01e2424a_b.jpg Thanks for following along! Mark |
Beautiful wood combo...love the bearclaw symmetry...really looking forward to watching this build!!
|
Quote:
Mark |
Trim
With the plates joined and thinned it's time to get going on trim. The back center strip and the rosette need to be put together and I've picked the elements to make that happen.
https://live.staticflickr.com/65535/...0f5f3a87_c.jpg I'm starting with Snakewood. I've got a lot of it and it is super hard, has hardly any pores, it reacts very little to changes in heat and humidity changes. This is an excellent wood to start with https://live.staticflickr.com/65535/...0d6f0675_c.jpg Snakewood makes for great binding, fretboard, bridges etc. https://live.staticflickr.com/65535/...bc0bcfb0_c.jpg Next up is Blue Stain White Pine. This is from my own woods and is the result of the Mountain Pine Beetle that introduces a fungus into the dead wood which creates this awesome permanent blue green color https://live.staticflickr.com/65535/...b667966f_c.jpg I've been hoarding the foraged pieces, slicing it up and stickering it to dry https://live.staticflickr.com/65535/...28f4e5cb_c.jpg I've been selecting out the most interesting pieces for a lot of my trim work since I've moved here in the Green Mountains Those of you who regularly follow me here know I've been incorporating a lot of stonework into my guitars. I prefer it because it is a natural material and just offers some much to see. The closer you look the more there is to see. On this guitar I am using stone called Rhodochrosite. The color contrasts the Blue stain and accents the Plum wood https://live.staticflickr.com/65535/...7f1e6579_c.jpg This is a pretty large slab and offers a lot of variation for me to choose pieces from https://live.staticflickr.com/65535/...d8b9993c_c.jpg The first thing I have to do is test it out. How hard is it to cut and shape? This picture shows a test piece all slathered up in CA glue so I can be sure it doesn't loose its color when saturated with glue. https://live.staticflickr.com/65535/...829487d7_c.jpg https://live.staticflickr.com/65535/...f49c98d0_c.jpg I love how this goes with the woods. Now that I have everything in hand it's time to make something: https://live.staticflickr.com/65535/...f9f9022b_b.jpg Thanks for viewing! Mark |
That is a pretty darned impressive inlay on that back. Perfect blend of colors and a diversity of materials to create a perfect blend of all.
|
Let me second Tom's observation. That inlay is absolutely stunning!
|
All times are GMT -6. The time now is 04:57 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright ©2000 - 2024, The Acoustic Guitar Forum